Dcvh680g12ww Parts

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.

This #8-32 x 1/2 machine screw is a direct-fit fastener used to secure panels and internal components in compatible appliances, restoring proper fit and eliminating loose or rattling parts. What it does:

• Secures panels, brackets, trim pieces and small internal assemblies where the factory screw is required
• Restores proper component alignment and prevents vibration-related noise
• Replaces missing or damaged mounting screws that allow parts to shift or come loose
• Matches standard #8-32 machine-thread fastener sizing commonly used in appliance assemblies

• Disconnect power and unplug the appliance before servicing to reduce shock risk
• Use the correct driver to avoid stripping the head; a magnetized screwdriver can help hold the screw
• Tighten until snug—do not overtighten to avoid damaging threads or panels
• Inspect mating threads and replace if damaged; replace with identical thread size and length

This gas valve and pipe assembly controls and routes natural gas from the appliance inlet to the burner manifold, restoring proper fuel flow for ignition and stable burner operation. Designed as a direct-replacement service part. What it does

• Regulates and directs gas flow from the inlet to the oven/range burners.
• Enables proper ignition and stable flame for baking and broiling cycles.
• Works with the appliance's existing manifold and burner orifices to maintain correct gas delivery.

• Turn off gas supply and disconnect power before servicing; follow all safety procedures.
• After installation, check all fittings for leaks with an approved gas leak test (do not use an open flame).
• Replace only with the exact part specified for your appliance; inspect connections and gaskets and tighten to manufacturer torque specs.

This OEM replacement part is the main control board for dryers. The main control board is the part that controls the functions of a dryer. It is the main component that sends signals to the dryer to perform its intended functions, controlling the desired dryer settings. If the dryer is no longer turning on, spinning properly, or effectively drying, it might be time to replace the main control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the dryer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board and be sure to take note of which wires go where by taking a photo with a phone camera. Then disconnect the air hose. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the air hose to the back of the control panel, and reconnect the wires into the back of the new control board.This genuine control board is compatible with General Electric, Hotpoint, RCA, and Sears/Kenmore brand dryers.

Specs: 8-32 ca hxw 1/2

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

This gas diffuser directs and evens the burner flame for reliable cooking performance. It helps stabilize heat distribution so burners light and heat more consistently across cookware. What it does:

• Spreads and evens gas flame to reduce hot spots and uneven cooking
• Helps stabilize burner ignition and maintain consistent flame shape
• Prevents direct flame contact with surrounding components
• Addresses symptoms like uneven heating, unstable flame, or partial burner operation

• One gas diffuser

• Turn off the gas supply and unplug the appliance before servicing
• Use basic hand tools; avoid overtightening or distorting the part
• If corrosion or sealed fasteners are present, replace affected hardware and check surrounding components

This motor support is the stamped metal bracket that secures the dryer motor and blower assembly, keeping components aligned for smooth operation. It restores proper motor mounting and reduces noise from loose or misaligned parts. What it does:

• Holds the dryer motor and blower housing in the correct position to prevent wobble or misalignment
• Helps maintain proper blower alignment for effective air movement
• Supports safe, reliable motor operation when the original bracket is bent, cracked, or worn

• Disconnect power (unplug electric or shut off gas and breaker) before beginning repair
• Access requires opening the dryer cabinet and removing the drum and/or front panel on many models
• Inspect related components (motor mounts, blower wheel, idler, belt) and replace if damaged

This ground screw secures the appliance chassis ground connection to the cabinet, restoring a reliable earth path for safe operation and reducing risk of electrical faults. Simple replacement keeps electrical components properly grounded. What it does

• Secures the ground wire or grounding strap to the appliance chassis to maintain a safe earth connection.
• Restores proper grounding when the original screw is missing, loose, or corroded.
• Helps prevent intermittent power/grounding issues and reduces risk of electrical arcing at the chassis connection.
• Works wherever a dedicated grounding point is required on the cabinet or frame.

• Single ground screw

• Always disconnect power (unplug or switch off circuit breaker) before servicing electrical connections.
• Verify chassis is de-energized and wear appropriate PPE when working on electrical parts.
• Use the correct driver bit and size to avoid stripping the screw; tighten securely but avoid over-torquing.
• Replace corroded grounding hardware and ensure the ground wire/strap has clean metal-to-metal contact.