Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more
The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.
This is a plastic selector knob that comes with a retaining clip, used on the washer's control panel to select cycle settings. It attaches to the control shaft and allows you to choose wash cycles and options. Replace this knob if it is cracked, broken, or if the clip has snapped, causing the knob to spin freely or fall off the shaft.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
Seals the lint screen housing to prevent lint bypass into internal components. Replace if lint escapes or seal is worn. Confirm fit with your model.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
The Interlock Switch is an OEM replacement part for GE electric and gas dryers. This safety component monitors the door closure, preventing operation if the door is not securely closed and latched. The switch measures 2 inches long and 1/2 inch wide.
Symptoms of a faulty interlock switch include:
Causes relate to the internal component contacting the door frame over 50,000 open/close cycles potentially exposing wiring to wear. Regular cleaning the external switch area prevents dust or lint buildup skewing performance.
This genuine GE switch is compatible with Hotpoint and RCA dryers as well.
Note: Can be used as a dishwasher door switch on specific models. Check your model number for the most accurate results.
The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more
White plastic door handle for dryer doors. Snaps into place on the front panel. Replace your cracked, broken, or missing handle for easier door operation.
My husband found the exact handle we needed to replace the one on our dryer at AppliancePartsPros.com and we ordered it. When it came, we replaced it. I know this sounds like a simple story, but honestly, it's much more. For weeks, this broken dryer handle was driving me crazy. Finally, my husband realized that AppliancePartsPros would likely have the part--and they did. We ordered the part on a weekend and got it on Monday. I couldn't believe it. We think this place is awesome. In the... Read more
Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.
I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more
The Igniter is an OEM part for GE dryers. It is designed to ignite the gas burner to produce heat, which is essential for drying clothes. The igniter ensures that the gas is lit efficiently and safely, enabling the dryer to reach and maintain the proper temperature for effective drying.
You should replace the igniter if it becomes faulty. Causes of a bad igniter can include electrical failures, cracks or breaks in the igniter material, or wear and tear from regular use. These issues can prevent the igniter from generating the necessary heat to ignite the gas.
Symptoms of a bad igniter include:
Changed ignitor. Ordered new ignitor by just putting dryer model number in the search box. When I opened the dryer up and took the old one out I was originally upset. The meter read 73 ohms. I was expecting OL (open line). The new one read 273 ohms so I put it in. Dryer works now. The install video’s are old. It was much easier than the video’s showed. Opening the control panel was a little trickier than the video. You do NOT need to take screws off the back of the dryer. There are 2 screws... Read more
Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.
Changed out high limit thernasstat Read more
The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.
Symptoms of a failing Door Strike include:
Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.
Note: If the door catch is also needed, use part number WE1M1011.
Replaced door strike and door latch Read more
A dual coil gas valve controls the flow of gas to your appliance's burners using two electromagnetic coils to open and close the valve. It regulates gas delivery to maintain safe, consistent flame operation. Replace this part if your burner won't light, gas flow won't shut off, or you notice uneven flames or a gas smell during operation.
I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.
Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.
Symptoms of a bad Door Latch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The gas valve solenoid controls gas flow to the dryer's burner assembly for heating during drying cycles. Located near the gas valve, replace it when the dryer won't heat, heats intermittently, or won't ignite properly.
The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.