Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.
Symptoms of bad bearings include:
Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.
This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.
Symptoms of a failing Door Strike include:
Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.
Note: If the door catch is also needed, use part number WE1M1011.
Replaced door strike and door latch Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.
Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.
Symptoms of a bad Door Latch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The Bearing Retainer is an OEM replacement part for GE electric dryers. It is an internal component that securely holds the drum bearing assembly in place to enable smooth rotation and provides structural bracing for the bearing during tumbling cycles.
Causes of a faulty retainer can include cracks from heat exposure over years of use. Impact damage from foreign objects inside the drum is also possible.
Symptoms of a bad bearing retainer include:
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.
Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.
Symptoms of a bad Clamp and Screw Kit include:
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:
I cut power to the dryer. I removed the face of the dryer. I then removed the felt mounts beneath the drum. I removed the old strips of felt and cut the new seal to fit both mounts. I then remounted the felt mounts and replaced the face. Read more
This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does
Package of 12
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.
Includes 12 screws. Size: 8-18 ab.
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you. Read more
A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:
Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:
7" diameter