We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Seals blower housing to prevent air leaks and lint escape. Replace when you notice lint buildup in your home or reduced drying efficiency. Confirm fit with your model number.
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
If your dryer takes too long to dry or overheats, the cycling thermostat may have failed. This part regulates heat by cycling on and off. Easy DIY fix.
I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
Ultimately is was discovered and caused by the blower wheel shaft opening was cracked and broken. Replaced blower fan wheel. Read more
6-foot flexible metal duct connects dryer exhaust to wall vent. Replace if crushed, torn, disconnected, or missing to restore proper airflow path.
Our heating element had broken coils. Typed model number in to see which parts were likely to fix the problem. AppliancePartsPros told me exactly which parts to try. For the cost, it seemed the best decision was to order the complete Heating Element Assembly, rather than risk needing the two smaller parts as well. Decided to order new vent as well. The parts arrived super fast and the on-site video showed step-by-step how to install the new part. From diagnosis to drying laundry in less than 48... Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
One of three coils, to get all three order 12001348
I ohm metered the sensors to determine which one was bad (open) Looked up the part on the parts drawing. Ordered part and had the dryer running 2 days later Read more
Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.
Dryer not heating properly or overheating? This cycling thermostat regulates temperature by cycling the heating element on and off. Moderate DIY repair.
Appliance won't start or trips breaker? This ground screw secures the grounding conductor to the chassis for safe electrical connection. Simple fix.
I ordered a new heating element and two other parts that attached to the heating element. I discovered a wire that broke off which caused the element not to work so I had to put a new female splicer on the broken wire then replaced the element and reattached the wires and everything worked. Read more
Size: 8-32 x 1/4 inch.
Exterior vent hood for dryer exhaust systems. Replaces cracked, broken, or missing vent covers. Installs at outdoor vent exit point.
Replaced switch assembly Read more
Dryer making rumbling noise or drying slowly? A worn blower wheel with a rounded center causes wobbling and poor airflow. Moderate DIY repair.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
Usually ships within 4 - 14 days
Lifter fin that mounts inside the rotating drum to tumble laundry. Replace if cracked, broken, or missing. Installs with screws for proper load movement.
Replaced with new Drum Baffles Read more
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.