Dpsr610ggwt Parts

This temperature switch mounts in the dryer control panel and lets you select the desired heat level. Replacing a failed switch restores accurate temperature selection so the dryer responds properly to the setting you choose.

• Selects the heat level for drying cycles
• Routes power through the appropriate heating circuit based on your selection
• Failure symptoms include no change in temperature when turning the knob, being stuck on one heat level, intermittent heat, or a loose/stripped switch shaft
• An internal short or open may contribute to a no-heat condition while the drum still runs

• Disconnect power before servicing; for gas dryers, also shut off the gas supply
• Remove the control knob and open the control console/back cover to access the switch
• Note wire positions; transfer connectors to the new switch one at a time to avoid miswiring
• Mount the new switch securely, reassemble the console, reinstall the knob, and test heat selection

Rear bracket and leveling screw assembly.

This burner assembly is the combustion head for GE gas dryers. It mixes gas and air and directs a stable flame into the heater housing, restoring consistent heat when the original burner is corroded, warped, or clogged.

• Directs the gas flame into the heat chamber for proper drying temperatures
• Works with the igniter, flame sensor, and gas valve to produce heat
• Typical failure symptoms: no heat or intermittent heat, long dry times, burner lights then goes out, unstable/yellow flame
• Physical issues can include rust, warping, or blocked burner ports

• Disconnect power and shut off the gas supply; allow the dryer to cool completely
• Note position of the igniter and flame sensor relative to the burner port; realign during reassembly
• Transfer any reusable fittings from the original burner as needed and verify orifice/fuel type match your installation
• After reconnecting gas, perform a leak check with a non-corrosive soapy water solution before restoring power

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This replacement screw secures panels, trims, and internal components to restore a snug, rattle-free fit and reliable operation. Use it to replace missing, corroded, or stripped fasteners for safe appliance performance. What it does:

• Fastens cabinet panels, trim pieces, and internal brackets to keep parts aligned and secure
• Replaces missing or damaged screws that cause loose or vibrating panels
• Prevents movement that can lead to wear, noise, or improper sealing
• Matches the original fastener role for appliances that specify part WE2M160

• Disconnect power or unplug the appliance before attempting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install until snug; avoid overtightening which can strip threads or crack plastic
• If threads are damaged or fastener holes are worn, replace damaged components.

Package of 12

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

This valve and pipe assembly controls water flow to the refrigerator ice maker and dispenser, restoring reliable water delivery and ice production. It replaces a worn or leaking water inlet assembly to stop drips and restore proper fill cycles. What it does

• Routes and controls water from the household supply to the ice maker and dispenser
• Opens and closes to allow timed water fills for ice production
• Stops water flow when the valve is closed to help prevent leaks
• Commonly used when the ice maker or dispenser does not fill or when visible leaks occur

• One valve and pipe assembly

• Turn off power and shut off the water supply before starting any repair
• Handle the valve and fittings carefully to avoid twisting or damaging water lines
• Use proper tools and replacement gaskets/filters where required; tighten fittings to manufacturer torque specifications

This door panel kit replaces the damaged outer front panel and the inner door panel to restore the oven door's appearance and structure. It keeps the door aligned and helps maintain a proper seal for safe, reliable operation. What it does

• Replaces a dented, cracked or warped outer front panel to restore cosmetic appearance
• Replaces the inner door panel to restore door structure and support
• Helps eliminate rattling, loose trim, or misaligned door fit
• Supports proper door closure and the integrity of the oven door assembly

• Disconnect power to the appliance before starting work; follow all safety precautions.
• Door removal is typically required; have a second person assist to prevent dropping parts.
• Handle panels carefully to avoid sharp edges and protect finishes.
• Use OEM fasteners and follow manufacturer instructions for reassembly and alignment.

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This gas valve and pipe assembly controls and routes natural gas from the appliance inlet to the burner manifold, restoring proper fuel flow for ignition and stable burner operation. Designed as a direct-replacement service part. What it does

• Regulates and directs gas flow from the inlet to the oven/range burners.
• Enables proper ignition and stable flame for baking and broiling cycles.
• Works with the appliance's existing manifold and burner orifices to maintain correct gas delivery.

• Turn off gas supply and disconnect power before servicing; follow all safety procedures.
• After installation, check all fittings for leaks with an approved gas leak test (do not use an open flame).
• Replace only with the exact part specified for your appliance; inspect connections and gaskets and tighten to manufacturer torque specs.

This replacement screw restores secure fastening for appliance components, helping stop loose panels and rattles. Use it to replace a missing or stripped fastener and keep assemblies aligned and stable. What it does

• Fastens panels, brackets, or small assemblies to maintain proper alignment
• Prevents vibration-related noise and movement from loose parts
• Replaces missing, worn, or stripped screws that allow components to shift
• Simple hardware solution that restores secure connections

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or nut driver to avoid cam-out or damage
• Start threads by hand to avoid cross-threading; tighten until snug
• Do not overtighten—excess torque can strip threads or damage parts