We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.
Tested the old t-stat with ohm meter. When shaken, the contacts would open. Replaced it with new t-stat and it works fine now. Thanks! Read more
Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.
I could hear the dryer motor hum, but it would not run. There was nothing obstructing the motor from turning freely so I assumed I needed a new motor. I went ahead and ordered a new pulley switch to change out while I was in there just in case. The parts arrived faster than expected. I changed the switch first and then checked the old motor which surprisingly fired right up. Now I have to decide whether to return the new motor or keep it as a spare. Read more
Replace your dryer's push to start button if cracked, broken, or worn. This button installs on the control panel. Commonly needs replacement due to wear.
Replaced the knob and it works perfect now Read more
This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.
Replaced thermal stats Read more
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Replaced the top bearing assembly, drive belt, and blower wheel. The most time consuming and difficult part was putting the new drive belt back on the pulley and tensioner. Be sure to know how it is routed through them. It is a very tight fit getting your arm in there and connecting it blindly. Read more
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more
Fix electrical grounding issues with this dryer ground strap assembly. Restores proper chassis grounding to reduce shock risk. Simple repair for worn connections.
This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.
Replaced the screw Read more
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
Converting your dryer from LP propane to natural gas? This conversion kit includes the orifice and components needed for a quick, straightforward swap.
Ordered the OEM conversion kit from you guys Read more
This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does
This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.
Installed the missing legs. Very east to do Read more
Fix a dryer that won't heat or cycles but doesn't ignite with this gas burner assembly. Restores consistent flame when the original is corroded or clogged.