We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.
Replace solenoid, flapper door and recess spring. Really only needed solenoid, but other parts were so inexpensive and I knew I would already be in there. Read more
Replaces broken or cracked refrigerator door stop. Installs on door to limit swing range and prevent cabinet damage. Needed when missing or worn.
Replaced upper and lower thimble's, lever arm, cam closure. Door stop was not the problem, but ordered it and replaced it too. The door of course has to come off, remove the top hinge, and lift it away. Lubricated moving parts with silicone spray. Be sure and put the door back in the open position, so the lever arm and cam closure can properly interact, then close the door. Remove the plastic grate at the bottom to get at the lever arm. Presto. Problem gone. Don't put excessive weight... Read more
Replaces the damaged or missing edge trim on your freezer shelf. Snaps onto the shelf frame to provide a finished lip and restore its original appearance.
Replaced with new parts. Read more
Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.
Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more
Replace cracked or broken ice bucket guide slides in your refrigerator freezer. Mounts to freezer wall to support and guide the ice bucket assembly.
Ordered right hand bucket glide and complete ice bucket assembly (cost more than just the cover, but did so in case other ice bucket assembly parts were worn out). Replacing bucket glide was done relatively easily by first turning off the icemaker, removing the old ice bucket assembly from the glides, removing all screws on the right hand glide, and loosening the screws on the left hand glide. This allowed the drive motor assembly (which fits in slots at the back of each glide) to move enough... Read more
Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.
Went online and looked for a parts dealer using the refrigerator model number. Read more
Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.
Very simple. Remove old grille (2 screws). Install new grille. Read more
Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.
Refrigerator not cooling or running constantly? This compressor powers your cooling system. Advanced repair, allow 2-4 hours for replacement.
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
White rear motor cover for refrigerator. Shields motor and fan area at back of compartment. Replace if cracked, broken, or missing to protect components.
Pictures on website were great. I ordered the part needed. Very easy to replace. Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket. Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.
My husband ordered and replaced the water tank inside the refrigerator in the back. Read more
This white ice dispenser paddle is the lever you press on the freezer door to release ice. Replacing a worn or broken paddle restores reliable ice dispensing and a clean, like-new look at the dispenser.
After reading posts on the problem I concluded that the motor and solenoid was OK because I was getting water shooting out in the water line before the water entered the freezer door. At the bottom of the door there is a quick disconnect to check the water before it goes into the freezer door. So, I concentrated on looking at the mechanism that dispensed the water because I read a post that said that the water usually freezes right in the hose before it comes out of the dispenser. I used a... Read more
Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.
Ordering the above parts I was able to solidly secure and align fan which got me up and running. Easy fix. Read more