Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.
Replaced with new parts. Read more
Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.
By using my socket set Read more
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
Me and my husband fixed it. Thanks for the help. Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Replaces a broken, cracked, or missing freezer shelf module in side-by-side refrigerators. Installs in factory side supports for organized storage.
Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.
My husband ordered and replaced the water tank inside the refrigerator in the back. Read more
Replacement trim for the dairy compartment on your refrigerator door. Restores a clean, finished look when the original is cracked, broken, or missing.
Replaced them. Read more
This is a refrigerator ice and water dispenser drip tray located on the freezer door. Color: White. It measures about 8 inches wide by 4 inches deep. For black order WR17X11655.
Ordered the new interface display - this must be the easiest refrigerator repair possible. My version popped right off without even a screw (some models have a screw). There are 3 different sizes of connector to disconnect and hook up to the new board - so you really can't mess that up. Read more
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
Bottom hinge that supports the refrigerator door weight and serves as the pivot point. Replace if worn, cracked, or causing door misalignment and sagging.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.