Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Usually ships within 4 - 14 days
Dishwasher tub assembly forms the main interior basin where dishes are washed. Replace if cracked, warped, or leaking at seams. Complete tub structure.
Size: 8-32.
This small plastic clip prevents your dishwasher's upper dish rack from sliding too far forward when pulled out. It stops the rack at the proper position to prevent it from falling out completely. Replace this clip if your upper rack slides out too far or falls off its tracks when loaded with dishes.
I replaced the parts. The video on the website was great. I'm glad I was able to find repair parts for such an old dishwasher. I'm squeezing as much life out of this unit as possible. Thanks. Read more
The Latch Switch Kit, an OEM Replacement Part is designed to ensure the safe operation of your Whirlpool dishwasher. The kit includes two microswitches and a wiring harness. It prevents the appliance from running when the door is open. If defective, the door switch may prevent the dishwasher from operating even when the door is closed.
Causes of a bad door switch can include wear and tear, exposure to moisture, or a broken actuator.
Symptoms of a bad door switch include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I ordered the Door Switch Kit, along with a few other items. However, the switch kit was all that was needed. Isimply followed the instructions that came with the kit. It was necessary to cut the wires which connected to the wire assembly in the door of the dishwasher. I then connected the pieces from the switch kit and then connected the end pieces to the door. I closed the door, and started up the dishwasher. It worked as well as before. Read more
Door spring assembly with retainer for dishwashers. Installs between door hinge and frame to counterbalance door weight. Replace when cracked or broken.
I replaced both support springs. It took several tries to get the springs installed in the correct orientation, even though I had read--and thought I understood--the instructions. The retainer side pin must be fed through the slot with the adjustment notches, and then latch it in the proper notch. As my usual rule of thumb, I start in the middle notch, and adjust further if necessary. This time the middle notch was correct. I used a screwdriver handle as a wedge on the one side of the... Read more
Very easy to repair. All the parts fit perfect. Entire repair took 20 mins. Read more
Cleared out trash from pump. Made E-Z by your exploded views and videos. Replaced worn parts. Read more
This drain cover seal creates a watertight gasket between the washer's drain cover and housing to help stop leaks and keep lint and debris out of the drain pump area, restoring reliable drainage and reducing mess. What it does:
Color: Black. Other colors: For white use 3374011, for almond use 3374012.
Replaced part, took about 2 minutes to install. Part fit great. Read more
Installed new Collector W/check Valve on the bottom of the dishwasher tub. About a 30 minute job (including removing the dishwasher from the cabinets--water supply, drain, and power--and reinstalling it. It would be nice if the manufacturer supplied the rubber check valve separately--small piece of rubber about the size of a nickel, probably $1 to $2--instead of selling it only as part of a $38 assembly. Read more
I replaced the pump/motor assemble and the seal. Took less than 10 minutes to fix and that was with me thinking about it for 5 minutes before I started. Read more
This lower wash arm bearing keeps the dishwasher's lower spray arm turning smoothly so dishes get even water coverage. It replaces a worn bearing to reduce noise and restore proper spray-arm rotation. What it does:
After discovering that these parts were not the problem. I found replacements for the impeller online and replaced those parts plus these parts. Disassembly was difficult and one bolt inside of the motor shaft had to be drilled out. Other than that, these replacement parts were an exact fit and the video on your page made the replacement no problem. Read more
Installed new washer took 5 minutes Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.