Du915pwkso Parts

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This pump and motor assembly circulates and drains dishwasher water to ensure proper washing and draining. It restores normal water movement so dishes get cleaned and the tub drains after a cycle. What it does:

• Circulates wash water through spray arms for effective cleaning.
• Pumps water out of the tub during drain cycles.
• Can cause noisy operation, poor cleaning, standing water, or failure to drain when defective.
• Works as the combined sump/pump motor unit used in many Whirlpool-family dishwashers.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Turn off the water supply and remove lower access panels to reach the pump/sump area.
• Handle as a single assembly; check and clear any debris or foreign objects from the sump and inlet before reinstalling.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This seal kit is for the main tub. It goes around the pump housing.

Screw for wash impeller.

A replacement mounting screw to secure appliance panels and components so parts stay properly fastened during normal use. Small but essential hardware for stable, rattle-free operation and reliable repairs. What it does:

• Fastens panels, brackets or components to the appliance chassis
• Prevents loose panels, vibration noise, or parts shifting during operation
• Used when original screw is lost, damaged, or stripped
• Restores proper fit and alignment after disassembly for service

• Disconnect power and water before starting any repair
• Use the correct screw type and length; do not force or substitute oversized fasteners
• Tighten until snug—avoid overtightening to prevent stripped threads or cracked parts
• Keep small parts away from children and pets

This pump outlet directs drained water from the washer's pump housing into the drain hose, helping the appliance remove wastewater efficiently. Replacing a damaged outlet restores proper drainage and reduces leaks. What it does:

• Channels water from the pump to the drain hose to enable normal draining
• Seals the pump discharge to prevent leaks at the pump exit
• A cracked or clogged outlet can cause slow or no-drain symptoms, leaks under the washer, or water pooling
• Works with the pump assembly to maintain correct water flow during drain cycles

• One pump outlet and the part shown as item 13 in the OEM diagram

• Disconnect power (unplug or switch off breaker) before beginning service
• Turn off and disconnect water lines if needed and place towels to catch residual water
• Inspect and replace any worn clamps, gaskets, or seals when installing the outlet
• Recheck connections and test a short drain cycle after installation to confirm no leaks