Dvm71955k4ss Parts

This white door handle assembly restores a secure, comfortable grip for opening and closing the appliance door. Replace a cracked or loose handle to maintain safe, reliable use and refresh the appearance.

• Provides the handhold used to open and close the door
• Replaces cracked, broken, loose, or missing handle
• Helps if the door is difficult to open due to a failed handle
• Refreshes the look when the original is stained or yellowed

• Disconnect power before servicing; allow the unit to cool if recently used
• Access handle mounting screws from inside the door by removing the inner trim/panel as applicable
• Support the door and glass while removing/installing hardware; transfer any spacers or caps from the original handle
• Tighten screws evenly without overtightening; verify smooth door operation

This stainless steel microwave door handle restores a solid, comfortable grip for opening and closing the door and refreshes the appliance's appearance when the original handle is damaged or worn.

• Attaches to the door and serves as the primary handhold for opening and closing
• Replaces cracked, loose, or missing handles
• Helps address difficulty opening the door caused by a damaged handle
• Matches stainless models for a consistent, factory look

• Disconnect power to the microwave before servicing
• Access the handle's mounting screws from the inside of the door; carefully release the inner trim to reach fasteners
• Support the door while working and start screws by hand
• Do not overtighten mounting screws to avoid damaging the door panel

A magnetron thermostat that helps prevent the microwave's high-voltage magnetron from overheating, protecting the component and helping restore proper heating when the original thermostat fails. Installs behind the microwave's magnetron assembly. What it does

• Acts as a thermal cutoff for the magnetron to stop operation if temperatures exceed safe limits.
• Common symptom: microwave runs but does not heat or heats intermittently.
• Common symptom: appliance shuts down unexpectedly or trips thermal protection.
• Helps prevent damage to the magnetron from sustained overheating.

• One magnetron thermostat

• Install only with power disconnected; high-voltage microwave components can store lethal charge—discharge the high-voltage capacitor before service.
• Verify correct part fit and orientation behind the magnetron; follow OEM wiring and mounting locations.
• Only replace this part if the existing thermostat is confirmed faulty; check related components (magnetron, high-voltage diode, capacitor) as needed.

This factory glass panel replaces a cracked, shattered, or missing original, restoring a clean, safe cover/viewing surface on your appliance. It helps protect internal areas from splatter and keeps the assembly looking and fitting the way it should.

• Replaces a damaged glass component within the original assembly on applicable models
• Restores a clear, smooth surface for proper appearance and function
• Helps shield underlying parts from spills, grease, and debris
• Common symptoms: cracked or shattered glass, missing piece, sharp edges, looseness/rattling

• Disconnect power before servicing; allow all surfaces to cool
• Wear cut-resistant gloves and eye protection; handle edges carefully
• Support the panel/door during removal and installation to prevent stress on frames/hinges

This holder nut assembly secures a component to the appliance frame, restoring proper mounting and reducing vibration or movement. Replace a damaged or missing holder nut to keep connected parts stable and functioning. What it does:

• Secures a component or assembly to the appliance frame or mounting bracket
• Prevents looseness, rattling, and misalignment caused by worn or missing mounting hardware
• Restores a safe, stable connection that helps maintain normal operation
• Matches OEM mounting geometry for a direct replacement when the original nut is damaged

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the mounting area by removing the appropriate panel or cover per your model's service instructions
• Start threads by hand to avoid cross-threading, then tighten with the correct tool; do not overtighten
• If any fasteners or nearby components are damaged, replace them as needed for a secure installation

This latch body is the plastic housing for the door interlock system. It holds the door switches in position and guides the door latch so the appliance can sense when the door is closed and operate safely.

• Holds and aligns the door interlock switches
• Guides the latch to properly engage/disengage when the door opens and closes
• Can help resolve issues like the unit not starting, running with the door open, or showing door error messages
• Restores proper, safe door sensing and operation

• Unplug the appliance to disconnect power before servicing
• Access is typically from the front; remove necessary panels to reach the latch body and switches
• Transfer switches and hardware from the old housing to the new one as configured
• Verify correct switch orientation and secure mounting before reassembly and testing

This cooktop lamp socket is the replacement holder that secures the cooktop bulb and provides the electrical connection so interior or surface lights work reliably. Restores proper bulb seating and electrical contact for safe lighting. What it does:

• Holds the cooktop light bulb in place and provides the electrical connection to power the lamp
• Re-establishes a secure contact if the original socket is loose, burned, or cracked
• Helps resolve symptoms like a bulb that flickers, won't stay lit, or fails to power on
• Compatible with standard cooktop light bulbs used in many GE cooktops

• One cooktop lamp socket

• Disconnect power to the appliance before servicing to avoid electric shock
• Inspect wiring and terminals for damage; replace any frayed or heat-damaged wires
• Securely seat the bulb and test operation before reassembling the cooktop

This temperature control thermostat regulates refrigerator temperature to help keep food cold and maintain proper cooling cycles. Replaces a failing mechanical control to restore consistent compressor on/off operation. What it does:

• Senses cabinet temperature and signals the compressor to cycle on and off
• Helps correct symptoms like inconsistent temperature, fridge running constantly, or not cooling
• Works with mechanical capillary-style temperature control systems
• Restores user control over interior temperature settings

• Disconnect power to the appliance before starting any repair
• Handle the capillary tube and sensing bulb carefully—avoid kinks or sharp bends
• Verify proper routing and secure mounting of the bulb per the original layout

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

The Magnetron Thermal Cut Off is an OEM part for GE microwave ovens. It is a safety component that protects the magnetron tube from overheating.

Symptoms of a bad magnetron thermal cut off include:

• Inability to heat or cook food  
• Repeated blowing of fuses or tripping of circuit breakers
• Magnetron tube failure due to lack of overheat protection

Causes can be wearing out of the component over many heating and cooling cycles. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore microwave models. 

Protective cover that shields the appliance's management/control assembly and internal wiring from dust, debris, and accidental contact. Helps keep controls insulated and reduces the chance of damage to internal components during normal use. What it does:

• Covers and protects the appliance control/management module and wiring harness from physical damage and contamination.
• Helps prevent accidental contact with live components that can cause shorts or shock hazards.
• Replace if the cover is cracked, broken, missing, or if exposed wiring is visible.
• Can reduce rattling or vibration-related noise when a broken cover allows movement of internal parts.

• Always disconnect power to the appliance before beginning any repair.
• Handle edges carefully; part and surrounding areas may have sharp metal or plastic tabs.
• Reuse original fasteners unless damaged; ensure cover is seated and secured to avoid interference with moving parts.

This safety cover protects internal wiring and components by enclosing delicate parts and helping prevent accidental contact. It restores a safe barrier and helps avoid shorting or debris buildup in the affected area. What it does

• Covers and protects wiring, connectors and nearby components from contact and debris
• Helps prevent accidental electrical contact and reduces risk of shorts where the cover is installed
• Commonly replaced when the original cover is cracked, melted, broken or missing
• Helps restore proper component spacing and secure mounting of nearby parts

• One safety cover

• Disconnect power to the appliance before servicing; verify it cannot be energized
• Remove panels or trim as needed to access the cover; keep fasteners for reinstallation
• Align mounting tabs or screw holes and secure with the original hardware
• If wiring or components show damage, replace or repair those items before reinstalling the cover

A small plastic retainer that secures the appliance control board in its housing to prevent movement and intermittent connections. Keeps the control board seated for reliable operation and reduces rattle or contact issues. What it does

• Holds the electronic control/PCB firmly in place inside the console or chassis
• Prevents board flexing that can cause loose connectors or intermittent faults
• Reduces vibration noise and rattling from a loose control board
• Helps maintain proper alignment for wiring harnesses and connectors

• One board latch (single retainer as shown)

• Disconnect power to the appliance before servicing to avoid shock or damage
• Remove the console or housing cover to access the control board; handle the board by its edges
• Snap the latch into the designated mounting posts until it securely engages the board

This assembly fuse restores overcurrent/thermal protection to the appliance's electrical circuit, helping stop power loss and intermittent operation. Replace a failed fuse to return reliable power path protection and safe operation. What it does:

• Provides circuit protection by opening the circuit when excessive current or heat is detected
• Prevents further electrical damage by interrupting power during a fault
• Common symptom: appliance won't power on or shows intermittent/no power
• Common symptom: control or heating components lose function while other parts remain powered

• Disconnect power (unplug or switch off breaker) before replacing the fuse
• Verify the appliance is fully de-energized and wear appropriate PPE (gloves/eye protection)
• Replace only with the exact part number to maintain proper protection and fit

The Main Board is an OEM component designed specifically for GE microwaves. This main board is the central processing unit that regulates all microwave functions.

Causes of a bad main board can include normal wear and tear over time from heavy usage, accidental moisture or liquid damage, or failure of electronic components.  

Symptoms of a bad main board include:

• Microwave failing to power on or function  
• Presets or settings no longer working properly
• Display/control panel issues such as flickering or unresponsive buttons
• Timer malfunctions causing under or overcooking  
• Door switch malfunction preventing the microwave from running

This GE microwave main board is also compatible with some Hotpoint, RCA and Kenmore models.

This refrigerator thermostat controls and regulates the appliance's internal temperature, helping the cooling system cycle on and off to maintain set temperatures. It replaces a failed or inconsistent temperature regulator to restore proper cooling control. What it does:

• Senses internal cabinet temperature and signals the compressor/fan to cycle on or off
• Helps keep food safely chilled by maintaining the selected temperature range
• Commonly used when the refrigerator is too warm, too cold, or cycles erratically
• Replaces a damaged, stuck, or intermittent temperature control

• Disconnect power to the appliance before beginning any repair.
• Handle capillary tube and sensor elements carefully to avoid kinks or damage.
• Ensure correct mounting and wiring match the original; take photos before disassembly for reference.