Eid6105 Parts

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This is a replacement screw used to secure appliance panels and components, restoring proper fit and stopping looseness or rattling. It's a direct-fit fastener that helps maintain safe, stable operation when original hardware is missing or worn. What it does

• Secures panels, brackets, trim pieces or internal components in place
• Stops rattling or vibration caused by loose fasteners
• Helps maintain proper alignment of parts for reliable operation
• Restores missing or damaged mounting hardware

• Screw

• Disconnect power (and water if applicable) before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or parts
• Keep removed hardware organized before final assembly

The Duct Assembly is an OEM part for Frigidaire dishwashers. It helps to direct hot, moist air from the dishwasher to the condenser, where it is cooled and converted back into water.

A bad duct assembly can be caused by damage, blockage, or wear and tear. Signs of a faulty assembly include poor drying performance, excess moisture or humidity inside the dishwasher, or water leaks.

Symptoms of a bad duct assembly can include:

• Poor drying cycle
• Excess humidity inside the dishwasher
• Water leaks around the dishwasher 

Replace your damaged duct assembly with this genuine OEM part to restore your dishwasher. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Water Inlet Valve is an OEM part for Frigidaire dishwashers. It controls water flow into the washing chamber and various spray arms during different cycles. Located near the bottom of the dishwasher tub, the valve regulates water pressure and timing for the clean, rinse, and sanitize portions of the cycle.

Symptoms of a bad inlet valve include:

• No or weak water spray from the lower spray arm during wash cycles
• The dishwasher not fully filling with water  
• Drying issues after the cycle from insufficient rinsing
• Error codes and inability to run complete programs

Causes can be mineral buildup clogging the valve over time, failure from hard water conditions, or accidental impact during tub maintenance.

Replacing the inlet valve with a Frigidaire OEM part restores proper water distribution throughout the dishwasher. It is also compatible with dishwashers by Electrolux, Gibson, Kelvinator, and Kenmore.
 

No.7 plastic .375

Red

This O-ring seals the turbidity sensor assembly to help keep water contained and the sensor functioning properly. It's a small replacement seal for maintaining a watertight sensor connection and reliable turbidity readings. What it does:

• Seals the turbidity (water clarity) sensor housing to prevent leaks into the sensor area
• Helps maintain correct sensor operation so the control can monitor wash water clarity
• Restores a proper seal after sensor removal or repair

• Always disconnect power to the appliance before starting any repair.
• Remove the sensor assembly per manufacturer instructions; replace the old O-ring with the new one, ensuring it seats evenly in the groove.
• Inspect mating surfaces for nicks, debris, or old sealant and clean before installing the new O-ring.
• Use an appliance-safe lubricant compatible with rubber O-rings; avoid petroleum-based products unless specified.

This cap is a small sealing cover that helps protect and close off an appliance connection or opening, restoring a finished appearance and helping prevent dirt or moisture intrusion. It's a simple replacement for worn or missing caps. What it does:

• Covers and seals small ports, openings, or fastener heads to block debris and moisture.
• Restores a secure fit where an original cap has cracked, broken, or gone missing.
• Helps maintain proper appliance operation by preventing contamination of components.
• Works as a cosmetic replacement to conceal exposed hardware.

• Disconnect power and shut off water before servicing the appliance.
• Inspect the mating surface for damage or residue; clean before installing the cap.
• Press or snap the cap into place; avoid excessive force or prying that can damage the part.
• Replace any damaged retaining clips or grommets as needed for a secure fit.

This duct assembly routes air inside the appliance to maintain proper ventilation and system performance. Replaces a cracked or damaged duct to help restore correct airflow and reduce overheating or uneven operation. What it does:

• Channels airflow between internal compartments and vents for consistent temperature control
• Directs heated or cooled air to the proper areas to help maintain performance
• Helps prevent hot spots, poor cooling/heating, and related cycling issues
• Reduces rattling or abnormal noises caused by broken or loose ducts

• Disconnect power (and gas, if applicable) before starting any repair
• Handle carefully—edges may be sharp; wear gloves and eye protection
• Basic hand tools required; keep track of fasteners and gaskets removed during disassembly
• Test appliance operation after installation to confirm airflow and symptom resolution