Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Clear plastic meat pan for your refrigerator. Replace your cracked, broken, or missing meat drawer. Installs in the fresh food compartment.
Replaced them. Read more
Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more
Mounting bracket that secures the ice maker assembly to the refrigerator wall. Replace if cracked, broken, or missing to restore proper ice maker support.
Replaced the ice maker. The kit came with everything I needed to replace the ice maker. Parts that did not come with the kit were re-used from the old one. My Whirlpool refrig/freezer is an older model so the wiring harness that came with the kit was different from my existing. So instead of disconnecting the ice maker wiring harness from the freezer, I had to disconnect the harness at the ice maker. That was a b..... Anyway after about 20 minutes, finally unhooked the connector. I had... Read more
Cabinet roller axle supports refrigerator wheels for smooth movement. Replace if rollers wobble or fridge is hard to move. Verify fit with your model.
Left side wheels damaged from tenant running over floor register. Replaced all 4-rollers in rear and front of the refrigerator. Appliance Parts repair video was important to the success of the replacement. Read more
Replacement mounting screw for refrigerator panels, brackets, trim, and door handles. Restores secure fit when original fastener is missing, stripped, or corroded.
New handle Read more
1/4 inch compression nut for securing plastic water lines in refrigerators and ice makers. Replace worn, cracked, or missing nuts to prevent leaks.
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more
Magnetic door gasket creates an airtight seal to keep cold air in. Replace if worn, cracked, or not sealing properly to maintain temperature and efficiency.
Vertical duct that channels cold air from the evaporator through cabinet vents. Replace if cracked, broken, or blocked to restore proper airflow distribution.
Replaced the motor and fan blade. Read more
Supports the refrigerator door at the bottom pivot point. Replace if your hinge is rusted, bent, cracked, or broken to restore proper door alignment.
Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more
This ice maker shut-off arm is the wire lever that detects the ice bin level and stops production when raised. Replace a bent, broken, or missing arm to restore reliable on/off control of your icemaker.
Ordered a new ice maker from APP. All went well, did not think to keep shut off arm from old ice maker before I trashed it. Got lots of ice now. Read more
Fixes refrigerator not defrosting or freezer icing up. This adaptive defrost control board manages defrost cycles. DIY-friendly repair.
Replaced control board. Read more
Freezer Door Gasket
Metal support bar that mounts to the refrigerator liner to hold the crisper cover frame and glass level. Replace if broken, missing, or bent.
I had to cut down the length of the bar using a Dremel so that it would fit into the channels, it was originally too wide to fit into the fridge. One thing to note, only cut it as wide as the actual fridge; you can get it into the plastic shelf structure by sliding it too much into one side, and then guiding it into the other side. Read more
Refrigerator won't cool or makes clicking noise? Replace the compressor overload protector. This thermal switch prevents overheating. 1-hour DIY repair.
Replaced start relay and overload $45 fix. Thank you! Read more
Crisper drawer won't adjust humidity? This slide moves the vent door to regulate moisture in your produce bin. Snap-in replacement restores humidity control.
Cleaned the slide areas really well and ordered new drawers. Read more
Stops refrigerator fan rattling and buzzing noise. This rubber grommet cushions the fan motor to reduce vibration. Simple DIY fix, takes under 30 minutes.
Ordered the parts from you guys, evaporator fan motor, fan blade, and new grommets. unscrewed the inside back panel of the freezer, removed the old fan, installed the new one. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.