Fafw3511kro Parts

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This inner door frame forms the interior half of the appliance door. It holds the window and mounting points so the door aligns and latches correctly, replacing cracked or warped plastic that can affect closing performance.

• Forms the interior structure of the door and supports the window
• Provides mounting locations for hinge, strike/catch, screws, and trim
• Helps maintain proper door alignment and seal contact when closed
• Damage can cause misalignment, difficulty latching, rattling/loose window, or a door that won't stay shut

• Disconnect power; if servicing a washer, also turn off the water supply
• Remove the door, place it on a padded surface, and transfer the window and any door hardware to the new frame
• Reuse existing fasteners; tighten evenly and avoid overtightening into plastic
• Verify the door closes and latches smoothly before returning the appliance to service

The Drive Motor is an OEM part for Frigidaire washing machines. This motor powers the drum's rotation during both the wash and spin cycles. It ensures that the drum agitates and spins correctly, allowing for effective cleaning and rinsing of laundry.

Over time, the drive motor can fail due to regular wear and tear, electrical issues, or overloading the washing machine.  

Symptoms of a bad drive motor include:

• The drum not spinning or agitating
• Unusual noises or humming sounds during operation
• The washing machine stopping mid-cycle
• Burning smells coming from the motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

• One door window glass

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This electronic control board manages your appliance's core functions and timing. Replacing a failed board restores proper operation when controls are unresponsive or cycles won't run as designed. What it does

• Distributes power to key components and executes programmed cycles
• Monitors inputs from switches/sensors and controls motors, valves, and heaters as needed
• Can resolve symptoms such as no power to controls, won't start, or cycles not advancing
• Address intermittent operation, error codes/abnormal beeps, or unexpected shutdowns

• 1 electronic control board

• Disconnect power before servicing; verify no voltage is present
• Use ESD precautions and handle the board by the edges only
• Photograph/label wiring and move connectors one at a time to the new board
• Ensure all connectors are fully seated and the board is mounted securely before test

This water level pressure switch senses tub water level through an air hose and signals the control when to stop filling and allow spin. Replacing a failed switch restores proper fill levels and reliable cycle progression. What it does:

• Monitors water level via air pressure from the tub's air dome hose
• Signals the control to start/stop filling at the correct level
• Prevents overfilling and enables spin only when the tub is empty
• Common symptoms: overfills or underfills, won't fill, keeps filling, won't advance or won't spin

• Pressure switch

• Disconnect power and water supply before servicing
• Access the switch (typically under the top or rear panel) and release its mounting clip/screws
• Transfer wires one at a time; move the air hose to the new switch and ensure a tight, unobstructed connection
• Secure the switch and run a test fill/spin; inspect the air hose for kinks, cracks, or soap residue

This electronic control board is the main "brain" that directs your laundry appliance's cycles and powers key components. Replace a failed board to restore responsive controls, accurate cycle timing, and dependable operation. What it does:

• Coordinates cycle selection, timing, and status/display functions
• Interprets inputs from door/lock switches and sensors
• Switches power to loads such as the motor, heater, valves, or pump
• Common symptoms: blank/unresponsive controls, won't start, cycle won't advance, intermittent operation, or error codes

• 1 electronic control board

• Disconnect power before service; allow components to discharge
• Use ESD precautions; handle the board by its edges
• Photograph/label connections; transfer any brackets, spacers, or jumpers from the original board
• Seat connectors fully and run a test/diagnostic cycle after installation

Plastic door cover

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This genuine replacement screw secures appliance components and panels in place to keep your unit assembled and operating smoothly. Use it to replace a missing or damaged fastener so parts stay tight and properly aligned.

• Fastens brackets, panels, or assemblies as designed by the manufacturer
• Helps resolve loose or rattling panels caused by a missing/stripped screw
• Maintains proper alignment after service or repair
• Restores secure mounting when an original fastener is lost or damaged

• Disconnect power (and shut off gas/water if applicable) before servicing
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Replace any damaged clips or inserts the screw threads into

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection