Need Help?
Call or text
Traps lint and debris during drying. Replace when mesh appears clogged, melted, or reduces airflow. Confirm fit with your model number before ordering.
Simple fix, just replaced the screen with the new one I ordered from you Read more
Replacement door hinge for dryers. Installs on the door opening to enable proper opening and closing. Needed when hinge is cracked, broken, or worn.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Replace your dryer door gasket to restore an airtight seal and prevent heat loss. Installs in minutes—just pull out the old, snap in the new. Confirm fit.
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:
Fixed it in 5minutes. One end has a Phillips head screw and the other has a tab with to metal leads for wires. The end with the tab broke. I removed the screw for the other end abd the sensor bar came off. To put the new piece on, I connected the wires to the leads, slid the tab end into place on the drum and screwed in the other end. Done! Easy! Read more
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.
Screwed it on. The order shipped out the same day, arrived fast and on time. But I have to mention the customer service. The person helping me place the order was EXCEPTIONAL!!!! Very friendly and helpful. BEST customer service experience I’ve ever had. I was so impressed that I asked to speak to her manager. The manager was also exceptional. Very nice. I highly recommend this company. Read more
Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.
Installed new Asmy-Lamp and added new wire connectors to harness. Read more
Plastic door cover
Removed from dryer with screwdriver and opened door to access outer glass panel. Replaced with new one and reassambled. Read more
Dryer not starting or power cutting out? A melted or corroded terminal block disrupts power flow. This 3-terminal block restores secure connections. DIY-friendly repair.
While checking a no heat issue with dryer noticed that terminal block was melted due to loose connections, replaced terminal block with new and replaced heating element. Read more
Secures the fan housing to its mounting points. Replace if the clip is broken, missing, or worn to eliminate rattles and prevent air leaks in your dryer.
Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.