Ffld2426tw2a Parts

Mounting screw for range oven door handles. Secures the handle to the door panel. Replace when stripped, corroded, missing, or if handle is loose.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

The Knob is an OEM part for Frigidaire ranges and ovens. It is used to control the temperature and settings for the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.

You should replace this knob if it becomes damaged or worn out. Common causes of a bad knob include physical damage from impact, wear and tear from frequent use, or melting due to exposure to high temperatures.

Symptoms of a bad knob include:

• Difficulty turning the knob
• Knob slipping or not staying in place
• Cracks or breaks in the knob
• Inaccurate temperature or setting adjustments

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

Fix excessive shaking, banging, or off-balance errors caused by a broken suspension rod. This tub stabilizer absorbs movement during spin cycles.

Washer not filling with water or won't stop filling? This water inlet valve controls water flow into your washer. Moderate DIY repair for most models.

This is a cap that fits on top of the washer agitator, covering the bolt or fastener that secures the agitator in place. It provides a finished appearance and helps keep debris out of the agitator mounting area. Replace this cap if it is cracked, missing, or no longer snaps securely onto the top of the agitator.

Connects your washer tub to household plumbing to drain water after each cycle. Replace if cracked, kinked, leaking, or too short for your installation.

The Heater Assembly is an OEM part for Frigidaire laundry centers. It functions to safely provide the heat necessary for multiple laundry cycle options including both washer and dryer modes. The assembly works through an electric heating element to heat filtered air throughout clothing loads in the combined washer/dryer unit.  

Causes of a failing heater assembly can include cracks or breaks in the coil insulating material allowing short circuits over many uses. Mineral buildup on heating surfaces can reduce heat transfer efficiency as well.

Symptoms of failure include:

• Extended or unfinished dryer-mode cycles  
• Tripping of internal thermal cut-off devices
• Loose, burnt, or cracked wires in the assembly housing
• Abnormal smells or smoke during operation

Compatible models include those by Kenmore, Crosley, and Inglis. 

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

Replacement burner head for gas ranges and cooktops. Mounts over the orifice to distribute flame evenly. Needed when original is cracked or damaged.

Fix a washer that only fills with cold water or won't fill at all. This water inlet valve controls hot and cold water flow during wash cycles.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.