Ffld2426tw2a Parts

• Will not tumble

I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more

Replaced igniter. Problems solved. Read more

• Oven is too hot
• Little to no heat when baking
• Won't start

Removed and replaced Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• No heat or not enough heat

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

Replaced the belt. Read more

• Marks left on clothes
• Noisy

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

I researched online and found that it was probably one of two things wrong: the heat probe or the control board (clock). Since the probe was less expensive, I ordered that on Appliance PartsPros. It arrived SO quickly, and with the repair video I easily replaced it. BUT... it still got the F10 reading. Sigh. So I found a local appliance repairman (I didn't want to replace a more expensive item if it turned out I was wrong). He was a good one: he listened to my story, said he was sure it was the... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more

• No heat or not enough heat
• Takes too long to dry

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

• Door won't close
• Won't start

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more