Fggc3035rfd Parts

The Valve is an OEM part for Frigidaire cooktops. It functions as an important component within the gas supply system that controls the flow of fuel between various points during each heating cycle. The valve works closely with the burner assembly and gas manifold to maintain consistent temperatures by facilitating proper circulation of gas throughout the system.

Symptoms of a bad valve include:

• Uneven or intermittent heating of burners  
• Burners that are difficult to light or stay lit
• Smelly gas odor coming from the range when in use
• Damage to other gas supply components requiring replacement

Causes of a bad valve can include mineral buildup over time restricting flow, failure of internal rubber seals preventing a tight seal, or issues in the valve's opening and closing mechanism.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This gas burner orifice meters fuel to the flame so your range or cooktop heats with the correct flame size and stable output. Replacing a worn or clogged orifice can help restore even flames and consistent cooking performance.

• Regulates gas flow through the burner jet for proper flame height
• Supports reliable ignition and stable, even flame characteristics
• Common signs of trouble: weak or uneven flames, yellow tipping, or delayed ignition
• Orifices are position- and fuel-specific; always match to your model and gas type

• Disconnect power and shut off the gas supply; allow the appliance to cool completely
• Remove grates, burner caps, and burner head as needed to access the orifice
• Use the correct wrench/nut driver; do not overtighten or alter the jet opening
• After reassembly, turn gas on and leak-check with a soap-and-water solution; verify flame per the manual

The Burner Valve is an OEM component specifically designed for Frigidaire cooktops. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Symptoms of a bad burner valve can include: 

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance   
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Causes of a bad burner valve include wear over extended usage periods, damage from water, or gas blockage impeding operation.

This OEM Frigidaire replacement is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.

This natural gas burner orifice meters gas flow to a specific burner on your range, delivering the correct flame size and heat output. Replace a worn or clogged orifice to restore stable, efficient burner performance. What it does:

• Meters natural gas to match the assigned burner's BTU rating and flame height
• Helps produce a steady blue flame and even heating when the correct orifice is installed
• Helps with weak/uneven flame, yellow tipping/soot, or delayed ignition if the orifice is blocked or damaged
• Fuel-specific component designed for natural gas systems

• One natural gas orifice

• Shut off gas supply and disconnect power before servicing
• Replace like-for-like; the stamped size/marking matches the burner position and fuel type—do not drill or modify
• Use an appropriate wrench and tighten snugly without overtightening
• Restore gas and leak-test with a soap solution; proper flame.

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This ignitor and orifice assembly provides the ignition source and gas orifice for a gas oven or range burner, restoring reliable ignition for cooking. Replaces a worn or damaged ignitor/orifice to help the burner light correctly. What it does:

• Supplies the ignition element and properly sized orifice so the burner can light and maintain a stable flame.
• Replaces burned-out or cracked ignitors that cause slow or no ignition.
• Replaces clogged or damaged orifices that can cause weak or uneven flames.
• Common symptoms it can address: burner won't light, repeated clicking with no ignition, or a weak/uneven flame.

• Turn off the appliance power and shut off the gas supply before servicing.
• Handle the ignitor carefully—the ceramic/sensing tip is brittle and can break if dropped or bumped.
• Disconnect electrical connectors and note wire positions before removal; reconnect exactly as found.

Note: Quantity of two brackets

Replace a worn or missing control knob and restore precise, dependable setting selection on your appliance. This knob press-fits onto the control shaft to provide a secure grip and smooth, consistent operation.

• Attaches to the control shaft on the front panel
• Lets you turn the control to select heat, temperature, or function settings
• Common symptoms: cracked hub or stripped insert; knob wobbles, slips, falls off, or won't turn the control

• Disconnect power before servicing; shut off gas supply
• Pull the old knob straight off; align the flat/D-shape on the new knob with the shaft and press fully into place
• Do not use excessive force or tools; avoid bending the control/valve stem

This top burner gas valve controls and shuts off gas to a single surface burner so you can ignite and adjust flame height safely. Replace a worn valve to restore precise burner control and dependable lighting.

• Regulates gas flow to one surface burner for reliable ignition and flame adjustment
• Acts as the on/off shutoff for that burner via the control knob
• Helps when a burner won't light even though the igniter clicks
• Helps when flame won't adjust smoothly or the knob binds/feels stripped

• Disconnect power and shut off gas supply before servicing
• Remove knob and access the control/manifold area to reach the valve; note tubing and mounting orientation
• Transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections with an approved gas leak-detection solution before restoring service and testing burner operation

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

The Surface Burner Valve is an OEM replacement part for Frigidaire cooktops. It is a crucial component that regulates the flow of gas to the individual surface burners on the cooktop. Each burner has its own valve, which allows precise control over the flame size and heat output.

Symptoms of a bad Surface Burner Valve include:

• Difficulty igniting or maintaining a consistent flame on the burner
• Uneven or flickering flame
• Burner not reaching desired heat levels
• Gas smell or leaks around the burner area

Causes of a bad surface burner valve can include general wear and tear over time, debris buildup or clogging, or physical damage to the valve or related components. Exposure to high heat or improper maintenance can also contribute to valve failure.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore cooktop models.

This surface burner seal sits between the burner and the cooktop opening to block spills and air leaks, helping the burner seat correctly and keeping the cooktop area cleaner.

• Creates a tight seal between the surface burner and the cooktop opening
• Helps prevent liquids and debris from getting under the cooktop
• Supports proper burner alignment and consistent heat/flame
• Replace if torn, brittle, swollen, or permanently compressed; common signs include seepage under the top, uneven heating/flame, or the burner not sitting level

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the cooktop to cool completely.
• Remove grates, burner cap, and burner head/base as applicable; lift off the old seal.
• Clean the mating surfaces; position the new seal evenly around the opening.
• Reassemble burner parts and test for proper seating and even heating/flame.

This assembly combines the spark igniter electrode with the orifice holder for a gas surface burner. It restores dependable ignition and proper gas delivery so the burner lights quickly and consistently.

• Provides the spark to ignite the surface burner
• Routes gas from the valve through the orifice holder to the burner head
• Typical symptoms: burner won't light, clicks but no flame, intermittent ignition, or cracked/chipped igniter insulator
• Replacing a damaged assembly restores reliable ignition at that burner

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner head; lift the top or access panel as your model requires
• Disconnect the spark wire, unfasten the old assembly, mount the new one, and reconnect the wire
• Restore gas and power, then check connections for leaks with an approved solution and test ignition

This is a ceramic glow-bar igniter for gas ovens. It heats to ignite the gas for baking or broiling, restoring reliable oven lighting and even heating without repeated clicking or open flames.

• Heats up to light the gas burner in the oven cavity
• Common fix for oven not heating, long preheat times, or burner that lights then goes out
• Designed for ovens that use a glow-bar (hot surface) ignition system

• Disconnect power and shut off gas before servicing
• Handle the ceramic element carefully; avoid touching the carbide tip
• Test for proper ignition and observe a full heat cycle after installation

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

Replacement mounting screw used to secure panels and small components on compatible appliances. Restores proper fastening to reduce rattling and keep trim, control panels and brackets aligned for safe, quiet operation. What it does:

• Secures panels, trim, brackets and other small appliance components.
• Replaces loose, missing or damaged fasteners that can cause rattling, gaps or panel misalignment.
• Restores mechanical stability for control panels and interior trim pieces.

• Disconnect power to the appliance before servicing any panels or components.
• Use the correct screwdriver and start the screw by hand to avoid cross-threading.
• Tighten securely but do not overtighten; replace if threads are stripped or the screw will not secure the part.