Fghb2866peo Parts

This replacement roller restores smooth sliding motion for a refrigerator drawer or bin along its track. Replacing a cracked or worn wheel helps prevent sticking, noise, and uneven movement that can strain rails and bins. What it does:

• Provides the rolling surface for a drawer, bin, or shelf track
• Restores smooth, consistent glide when opening or closing
• Helps reduce grinding/squeaking noises and binding
• Addresses issues like wobbling, tilting, or a missing/cracked wheel

• 1 roller

• Disconnect power before servicing
• Remove the drawer/bin to access the rail and roller
• Note the roller's orientation; transfer any reusable clips or fasteners
• Ensure the wheel spins freely and the drawer glides smoothly before reloading

Nylon

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This is the complete ice container assembly for the dispenser. It stores ice and drives cubes to the chute so your dispenser can deliver ice reliably and without jams.

• Holds finished ice in the freezer and feeds it to the dispenser
• Integrated auger moves and helps break up ice for consistent dispensing
• Common failure signs: ice not dispensing, auger not turning, loud grinding, or cracked/leaking bucket
• Restores proper in-door ice dispensing performance

• Unplug the refrigerator and remove the ice bin from the freezer door or shelf
• Transfer any remaining ice to a cooler; let any frost melt to avoid damage
• Align the drive coupling and slide the new bin fully into place
• Restore power and test ice dispense for cube and crush functions

This main power control board assembly is the refrigerator's central controller. It manages power to the compressor, fans, and defrost system so the unit cools consistently and responds correctly to temperature settings.

• Distributes and regulates power to the compressor, condenser/evaporator fans, and defrost components
• Processes inputs from temperature sensors and the user interface to coordinate cooling cycles
• Common symptoms it may address: not cooling or intermittent cooling, fans/compressor not running, unit won't defrost/ice buildup
• May also help with unresponsive controls or repeated clicking/buzzing from the control area

• Disconnect power before servicing; handle the board by the edges and use ESD protection
• Access location varies by model; typically mounted in a rear control compartment behind an access cover
• Photograph wiring and move connectors one at a time to the new board; ensure all locking tabs are fully seated
• Reinstall covers, restore power, and verify compressor/fans operate and cooling resumes

This thermistor is a temperature-sensing resistor that monitors internal temperature and reports it to the control. Replacing a faulty sensor restores accurate temperature feedback for proper operation and consistent, reliable cycle performance. What it does:

• Continuously measures temperature and changes resistance for the control to read
• Helps regulate heating/cooling and overall cycle timing
• Supports safety logic that prevents improper temperatures
• Failure may cause inaccurate temperatures, long/short cycles, or temperature-related error codes

• 1 thermistor

• Disconnect power before servicing; shut off water or gas if applicable
• Access the sensor, note wire routing/orientation, and transfer any existing clip or seal as needed
• Make secure electrical connections and route wires away from hot or moving parts
• Many appliances use multiple sensors—diagnose with an ohm/diagnostic test before replacement, then run a test cycle after install

This dispenser control board is the electronic module behind the refrigerator's ice/water dispenser panel. It reads button inputs and powers dispenser functions to help restore reliable dispensing and front-panel control when the original board fails. What it does

• Processes user selections for water, cubed/crushed ice, and dispenser light (model-dependent)
• Sends power to the water inlet valve and auger/dispenser motor as commanded
• Manages dispenser lock and status/display indicators (if equipped)
• Failure symptoms include unresponsive or intermittent controls, no water or ice dispensing, or an inoperative dispenser light

• Includes 1 dispenser control module (electronic board)

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Remove the dispenser escutcheon/cover to access the module; release locking tabs or screws as needed
• Transfer wire connectors one at a time to the new board, confirming orientation and full seating
• Reassemble, restore power, and test all dispenser functions

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This replacement block is a small structural component used inside the refrigerator to locate, support, or align its mating parts. Replacing a worn or broken block restores proper fit and helps keep the affected assembly secure. What it does:

• Provides a stable mounting/locating point for the applicable assembly
• Helps maintain alignment and reduces wobble or looseness
• Common failure signs: cracks, missing piece, or stripped fastener hole
• Symptoms may include rattling, sagging, or parts that won't stay in place

• 1 block

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove items and any obstructing parts to access the block; note orientation for reassembly
• Transfer any reusable hardware from the old block and secure the new block without overtightening
• Restore power and verify proper fit and operation of the serviced area

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed