Fgm0205kfb Parts

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Heat-resistant insulation that wraps the oven cavity to contain heat. Replace if worn, damaged, or missing to improve heat retention and efficiency.

Fix a microwave turntable that won't rotate with this motor replacement. Solves spinning issues when motor receives power but fails to turn the tray.

Spring-loaded hinge that supports and controls oven door movement. Replace when worn, broken, or door won't align properly for a secure seal and heat retention.

Fix a range cooling fan that won't shut off or makes howling noises with this motor. Requires removing oven from cabinet and back panel access.

Oven won't maintain temperature or exterior gets too hot? This insulation blanket contains heat and protects nearby components. Moderate DIY repair.

This switch/fuse kit replaces a worn or failed control switch and associated fuse to restore reliable power control. It provides the exact components needed to address common start and power interruptions. What it does:

• Replaces a faulty control switch to restore on/off or cycle control
• Replaces the protective fuse to stop power loss from a blown fuse
• Helps resolve no-start, intermittent power, or control failures
• Restores proper electrical continuity for safe operation

• Disconnect power to the appliance before starting any work
• Handle electrical components carefully and avoid metal contact with terminals
• Verify correct part orientation and secure all connections per OEM guidance

Microwave door won't stay closed or latch properly? This door latch assembly restores secure closure and proper alignment. Easy DIY repair.

This infinite switch controls the heat level for an electric cooktop surface burner, restoring adjustable power to the element for even cooking and reliable temperature selection. What it does:

• Regulates electrical power to a single surface heating element so you can set low-to-high heat.
• Provides stepped "infinite" control positions rather than a simple on/off.
• Replaces a worn or failed control that causes a burner to not heat, stay stuck on one setting, or heat inconsistently.
• Uses standard spade-terminal connections found on many electric ranges.

• Disconnect power at the breaker before servicing—this part services live-voltage circuits.
• Access typically requires removing the cooktop or rear console; handle ceramic glass cooktops carefully to avoid cracking.
• Confirm terminal layout and mounting orientation before removal; take a photo of wiring for reassembly.

Flexible door seal creates an airtight barrier to maintain proper oven temperature and energy efficiency. Replace if worn, cracked, or loose. Verify fit.

This refrigerator door gasket replaces a worn or damaged outer door seal to help maintain an airtight closure and improve cooling efficiency. It restores a proper seal to reduce drafts, moisture buildup and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and water accumulation on the cabinet floor
• Reduces compressor run time by maintaining consistent internal temperature
• Common symptom: visible cracks, tears, or areas that no longer seat against the cabinet
• Common symptom: warm spots at the door edge or excess condensation

• One refrigerator door gasket

• Disconnect power to the appliance before beginning any work
• Remove the old gasket by loosening retainer screws or pulling out the retainer, then press the new gasket into the retainer channel, working around the perimeter
• For tight fits, gently warm the gasket (low heat) to make it more pliable—do not overheat or use open flame
• Inspect the seal for even seating and, if applicable, torque retainer screws to manufacturer spec

Oven not heating or baking unevenly? This bake element restores consistent heat for baking and roasting. Moderately easy DIY repair in 30-45 minutes.

Microwave won't turn on or has no power? This fuse and holder assembly restores overcurrent protection when a blown fuse interrupts operation.

A replacement tension spring used to restore normal movement and positioning for the affected appliance component. Replaces a worn or broken spring to help parts return to their intended position and reduce loose or uneven operation. What it does:

• Provides tension or counter-force for a door, drawer or linkage so the part moves smoothly and returns to position.
• Restores alignment and prevents sagging, slamming, or parts that don't stay in place.
• Reduces noise and uneven movement caused by a stretched or broken spring.
• Useful when a worn spring causes intermittent operation or poor component response.

• Disconnect power and water before servicing. Wear eye protection and gloves — springs can release suddenly.
• Inspect mounting points, clips and anchors; replace any damaged hardware to ensure proper function.
• Use appropriate tools (needle-nose pliers, spring hook) and follow OEM instructions for safe installation.

This main electronic control board manages core refrigerator electronics for temperature regulation, defrost timing and the user interface. Replacing a failed control board can restore proper electronic response and system control when the unit is unresponsive. What it does

• Controls compressor and evaporator/condenser fan operation; failure may cause no cooling, constant run, or short cycling.
• Manages automatic defrost cycles and defrost heater operation; failure can result in excess frost or defrost errors.
• Sends and receives signals to the user interface and display; symptoms include blank, unresponsive, or erratic controls.
• Monitors sensor inputs and system status and helps coordinate system functions; may trigger error codes or incorrect temperature behavior.

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Handle the PCB by its edges and avoid static damage — use anti-static precautions if available.
• Photograph or label all connectors before removal so wiring is reinstalled correctly; secure all connectors and fasteners during reassembly.