Flcg7522aw2 Parts

The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.

Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage. 

Symptoms of a bad dryer ball include:

• Squeaking or grinding noises during operation
• The drum not rotating smoothly or becoming unbalanced
• Increased friction leading to higher energy consumption
• Visible wear or damage to the ball

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Board Assembly is an OEM replacement part for Frigidaire laundry centers. It serves as the main control board, governing the operations and functions of the combined washer and dryer unit.

Symptoms of a bad board assembly include:

• The laundry center not turning on or responding to inputs
• Erratic behavior or incorrect cycle settings
• Specific wash or dry cycles failing to start or complete properly
• Error codes or warning lights displayed on the control panel

Causes of a bad board assembly can range from power surges or electrical spikes, to component failure due to age or wear and tear. Moisture or water damage can also compromise the functionality of the control board.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore laundry center models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This washer door lock secures the door closed and communicates locked status to the control so cycles can run safely. Replacing a failed lock restores proper latching and may resolve no-start, spin, or door/lock error issues.

• Locks the door at the start of the cycle to prevent opening during wash and spin
• Signals the control when the door is closed and locked
• Releases the door at the end of the cycle
• Common symptoms: won't start, door won't lock/unlock, intermittent pauses, door/lock error message

• Unplug the washer before servicing
• Access the lock from the front; remove the door gasket clamp and mounting screws (procedure varies by model)
• Transfer wires to the new lock one connector at a time; do not force terminals
• Verify the door striker engages smoothly and test an empty cycle before full use

The Striker is an OEM component specifically designed for Frigidaire laundry centers. It connects the door to the stainless steel panel, providing secure closure of the unit.

Symptoms of a bad striker include: 

• Loose or misaligned door that does not fit properly
• Latching issue causing the door to open unintentionally  
• Failure points developing around striker mounting location
• Over time increased stresses on other door closure parts

Causes of a bad striker can be normal wear from repeated door openings, damage during moves impacting door alignment, or loose fasteners compromising connections.  

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore laundry center models. Replace promptly before needing other repairs.
 

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

The Door Switch is an OEM part for Frigidaire clothes dryers. It is an electronic component located on the door frame that detects when the dryer door is latched closed. The switch communicates this information to the control board, allowing the dryer to operate properly by preventing operation if the door is open.

Causes of a bad door switch can include normal wear and tear from opening and closing the dryer door over time. Physical damage from accidental impacts or overtightening of door mounting hardware may also cause switch failure.

Symptoms of a bad dryer door switch include:

• The dryer starting a cycle even when the door is open
• Error codes or failure to start/run if the door switch does not detect proper closure
• Other control issues related to incorrectly sensing door position

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This actuator motor drives the washer's brake and clutch to shift the mechanism between wash and spin. Replacing a worn actuator restores proper shifting so the tub agitates and spins at the right times and cycles can complete.

• Actuates the brake and clutch to change between agitation and spin modes
• Positions the shift mechanism via a small geared motor
• Helps the basket start/stop smoothly during cycle transitions
• Common failure symptoms: no spin, no agitate, stuck in one mode, or repeated clicking from the drive area

• Disconnect power before servicing; allow moving parts to stop completely
• Access the actuator near the drive/brake assembly (location varies by model)
• Note linkage and actuator orientation; remove screws and disconnect the harness, then install the new unit the same way
• Reassemble and run a spin and agitation test or your model's diagnostic check to verify shifting

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

This suspension rod stabilizes the washer tub during wash and spin, absorbing movement to reduce shaking and noise. Replacing a weakened rod restores proper balance and helps prevent banging, off-balance interruptions, and excess wear on other components.

• Supports and centers the tub within the cabinet
• Dampens vibration and tub oscillation during agitation and spin
• Helps prevent the tub from striking the cabinet
• Symptoms of a failing rod can include excessive vibration/shaking, loud banging, "walking," off-balance/UL errors, or wet loads after spin

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Support the tub before removing the rod—spring tension is present
• Access from the top; release the upper retainer, then unhook the lower end from the tub mount
• Install in the same position/orientation as the original; replacing multiple rods together can help maintain balance

For a complete drum bearing and shaft kit order 5303281153.

This washer agitator drives the wash action by moving clothes through water and detergent. Replacing a worn, cracked, or slipping agitator restores proper turnover and cleaning performance in compatible top-load machines.

• Oscillates during the wash cycle to move laundry through water and detergent
• Helps circulate and distribute clothes for effective cleaning
• Engages the drive hub; wear can cause slipping or poor agitation
• Helps resolve: no/weak agitation, agitator not moving, poor cleaning results, or visible damage/looseness

• Disconnect power and shut off water before servicing; work inside the washer basket
• Remove the fabric softener dispenser and inner cap, then the agitator retaining bolt; lift the agitator straight up
• Align splines and seat the new agitator fully; reinstall and tighten the retaining bolt, then reinstall the cap/dispenser
• After reassembly, run a short cycle to ensure proper engagement and operation

The Agitator Cap is an OEM part for Frigidaire washing machines. It fits securely atop the central agitator shaft located inside the washing machine tub. During the wash cycle, the agitator cap rotates along with the agitator to help agitate clothes and ensure water is properly distributed.

Causes of a bad agitator cap can include wear and tear over time, exposure to excessive loads or loads containing sharp or abrasive items that cause damage.

Symptoms of a bad agitator cap include:

• Water not properly dispersing during wash cycles
• Agitator not rotating or moving as it should
• Excessive rubbing or grinding noises coming from the agitator area
• Damaged or missing pieces on the cap

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

The Drain Hose is an OEM part for Frigidaire washing machines. It connects the washing machine tub drain to the home's water supply lines, allowing dirty water to be drained away after each cycle. During operation, the drain hose facilitates the emptying of water from the washer once the wash and spin cycles are complete.

Symptoms of a bad drain hose include:

• Water not fully draining from the machine after cycles
• Puddles or leaks observed around the washer
• Blockages in the drain line preventing proper emptying
• Splitting, cracking or collapsing of the drain hose material over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.