Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Creates a watertight seal between the washer tub and cabinet. Replace if you notice water leaking during wash cycles. Verify fit with your model number.
Disassembled washer, found that 2 out of the 3 basket support legs had cracked through. Unfortunately, support cannot be bought except as an assembly, so had to spend almost $300 for the part. Bearings were worn, but not trashed, so I replaced them and the seal. Note, most parts places (including AppliancePartsPros.com) will only sell the bearings and seal as part of the rear tub assembly. The bearings are standard 6205 and 6206 sealed ball bearings, available from Grainger and many others for... Read more
Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.
Watched YouTube and ordered parts then replaced the parts and walla !!!! All was good. Read more
Threads into the washer base to adjust height and stabilize the unit. Replace if cracked, stripped, or missing to eliminate rocking on uneven floors.
Washer won't spin or makes noise? This retaining nut secures pump and motor components. Common cause of leaks and wobbling. Basic tools needed.
Took back off of washer and replaced parts. Read more
Size: 8-18 x 1/2 inch.
This replacement screw secures appliance components and panels in their proper position. Replacing worn, stripped, or missing hardware restores a tight fit, reduces vibration or rattles, and helps maintain safe, reliable operation per the manufacturer's design. What it does:
Fixes loud banging and excessive vibration during spin when suspension spring hangs loose. This bracket secures the spring to the cabinet for stable operation.
Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more
Fix a washer that stops mid-cycle or won't advance between wash stages. This actuator cam guides the lever arm movement for proper cycle transitions.
Replace the lever control arm and motor. Read more
This is a small hose that connects to the dispenser valve assembly inside the washing machine, directing water into the detergent or fabric softener dispenser. It ensures proper water flow to the dispenser during the wash cycle. Replace this hose if you notice leaking near the dispenser area, detergent not being flushed into the drum, or visible cracks and deterioration on the hose.
Changed upper plate & inlet hose real easy. Read more
This replacement lever is a small mechanical link that engages or releases its mating mechanism inside the appliance. Replacing a worn or broken lever restores crisp actuation and reliable operation of the related control or latch. What it does:
Old lever was gently pried off at each end while pinching retention axle clips. New unit snapped in place easily. Fill Valve was removed easily after removal of a single retention screw in the back. [and after turned OFF the Hot & Cold water supplies any removing hose attachment fittings from the two fill valve nipples]. The two electrical connectors [color coded] are then easily disconnected. The Fill Valve then is pushed to the side & up and then back into cabinet and gently lifted up and... Read more
Fix a washer that won't spin, makes loud noise, or smells like burning. This drive belt pulley guides the belt and reduces friction. Moderate DIY repair.
Took it apart and saw that the the bearings were worn down completely.. The front outer tub was cracked and leaking. We ordered both pieces to the outer tub and a new pulley. My washer is running like new now.. A little advice.. Do not over load your washer.. Maytag is a great brand but overloading them because there great washers, will wear down the parts inside.. I have teenagers who overload my washers to save them time but wasting my money on parts.. Being a single mom it's hard but I did... Read more
Creates a watertight seal in 3/8-inch compression fittings. Replace when hardened, cracked, or leaking to restore a drip-free connection. Verify size fits.
Tub bearing failure, basically the whole machine has to be taken a part. I've used appliancepartspros in the past so I came back. Quick shipping, parts ordered Thursday night and got here Monday. Take your time or you'll just cost yourself more money. I was lucky in that I did not have to buy the $568 inner tub because I found a bearing and seal kit on Amazon for $80. Historically appliancepartspros' website has been very accurate indicating in stock or not. It appears those days are gone. I... Read more
Fix washer not powering on, F01/F11 error codes, or cycle failures with a new central control board. DIY repair in about 1 hour. Video guide included.
Well after Two different appointments and TWO different sears technicians looked at my machine, one indicated the CCU was bad, replaced it and still nothing, the second tech indicated the MCU was bad, he placed the MCU on a emergency order, 6 days later still no part and the Sears parts department said the part would be on back order for a couple more weeks, UNACCEPTABLE! (O_o). I located AppliancePartsPros.com, found the part I desperately needed, made the call and placed the order by noon.... Read more
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do Read more
Fix F25 error codes or a drum that won't spin with this washer drive motor assembly. Restores proper agitation and spinning for effective cleaning.
Washer not dispensing soap or softener? A clogged or broken distribution nozzle prevents water flow to dispensers. Moderate DIY repair restores function.
I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.