Gfd65gspnsn Parts

This handle spacer fits between the door handle and the outer door panel on select front-load dryers. It restores the correct standoff so the handle mounts securely, reducing wobble and helping the door open and close smoothly.

• Maintains proper spacing and alignment between the handle and door panel
• Helps prevent handle wobble, rubbing, or sagging
• Replaces a cracked, worn, or missing spacer
• Common symptoms include a loose or uneven handle and difficulty opening/closing the door

• Disconnect power before servicing
• Support the door/handle, then remove the handle screws
• Note the spacer's orientation and location before removal; install the new spacer the same way
• Tighten screws snugly without overtightening; verify smooth door and latch operation

The Door Cover is an OEM part for GE dryers. Located on the external door, this cover protects the door lining while enhancing the dryer's aesthetic. It is responsible for safely concealing inner components from external impact or damage. 

Causes of a bad door cover can include cracks, chips, or discoloration from repeated opening and closing of the dryer door or other impact damage over time. Exposure to cleaning chemicals may also affect the integrity of the cover.

Symptoms of a bad door cover include:  

• Loose fit that does not properly cover the door lining
• Cracked, chipped, or broken door cover material
• Visible damage or deterioration affecting appearance
• Warping or sagging that prevents the door from closing fully

This part is compatible with Hotpoint, RCA, and select Kenmore dryer models.

The Grille Housing is an OEM part for GE dryers. Located at the front of the dryer, the grille housing covers and protects the drying drum opening. It is responsible for preventing lint buildup and maintaining airflow into and out of the dryer. 

Causes of a bad grille housing can include cracks or breaks from repeated cleaning or impact, as well as loose or worn fittings that no longer provide a proper seal. 

Symptoms of a bad grille housing include:

• Excessive lint accumulation around the dryer opening 
• Inefficient drying times due to blocked airflow
• Loose or misaligned grille that does not close properly
• Leaks around the drum opening when the dryer is running

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

The BLOWER WHEEL is an OEM part for GE electric dryers. It is housed within the blower motor housing and works to push air through the dryer ducting. During cycles, the rotating blower wheel creates crucial airflow that carries heated air through clothes to dry them efficiently.

Causes of a bad blower wheel can include cracked or broken wheel blades from normal wear and tear over time. Accumulations of lint on the wheel can also reduce airflow and efficiency.

Symptoms of a bad blower wheel include: 

• Insufficient or no air being pushed through the dryer ducting
• Abnormally long drying times and wet clothes after cycles  
• Excessive noise coming from the blower motor area
• Safety features possibly tripping due to motor overheating

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Maintain optimal airflow by replacing your blower wheel with this genuine OEM component.

The User Interface Board is an OEM part for GE electric dryers. Located at the control panel, it acts as the central processing unit that facilitates communication between buttons, displays, and electrical units. The user interface board receives input signals from the touchpad buttons and uses programming to trigger the correct dryer functions. It also powers the digital displays and sends output signals to govern components like the motor, thermostat, and timer. 

Causes of interface board failure can be water damage, fluctuations in current supply over time distorting circuits, or heavy impacts potentially dislodging connections.

Symptoms of a bad user interface board include:

• Non-responsive or unresponsive buttons
• Inaccurate readings on LED displays
• Failure to advance programs or time settings

Compatible with some Kenmore dryer models that contain GE control internals.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

This GE Door Hinge is an OEM replacement part for GE washing machines. Designed to match the exact specifications of your GE appliance, this door hinge ensures smooth and reliable operation of the washing machine door. 

The need for a replacement usually arises when the existing hinge suffers from wear and tear, accidental damage, or corrosion. A bad door hinge can lead to issues with the door closing properly, which might affect the washing machine's functionality or cause water leakage.

Symptoms of a bad Door Hinge include:

• Difficulty in closing or opening the washing machine door.
• A door that hangs unevenly or appears misaligned.
• Unusual noises or resistance when moving the door.
• Visible wear, rust, or damage on the hinge.
• Water leakage around the door area.

This GE OEM replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This radiant sensor is part of the gas dryer ignition circuit. It detects infrared heat from the igniter and burner so the gas valve only opens when ignition is present, restoring consistent and safe dryer heat.

• Detects heat from the igniter/flame and controls the gas valve circuit
• Enables safe ignition and helps maintain a steady burner flame
• Common symptoms: igniter glows but no flame, burner lights then goes out, no heat or intermittent heat, long dry times
• Used on gas dryer models

• Disconnect power and shut off gas supply before servicing; allow the burner area to cool
• Access the burner assembly; remove the lower/front panel as your model requires
• Move the wires, remove mounting screw(s), and install the new sensor in the same orientation; avoid touching the igniter
• If heating issues persist, also inspect the igniter and gas valve coils

This gas valve controls gas flow to an oven or range burner so the appliance can ignite and maintain heat safely and reliably. Replacing a faulty valve restores proper gas delivery and stable burner/oven operation. What it does:

• Regulates gas flow to the burner or oven burner assembly for ignition and sustained heating.
• Common symptom: oven or burners fail to light or the appliance won't heat consistently.
• Common symptom: burners light briefly and then go out or the oven won't reach set temperature.
• Works as the primary control between the gas supply and the appliance's ignition system.

• Turn off the appliance's gas supply and electrical power before starting work.
• Use proper tools and follow the manufacturer's service instructions; improper installation can cause gas leaks or unsafe operation.
• After install, check all connections for leaks with a soap-and-water test or follow local code requirements; do not use an open flame.

This Dryer Door is an OEM part for GE dryers. It is designed to provide a secure and airtight closure for the dryer, ensuring optimal performance and energy efficiency. 

The need for a replacement dryer door can arise from physical damage, wear and tear, or seal degradation. A compromised door can lead to several operational issues.

Symptoms of a malfunctioning Dryer Door include:

• Difficulty in closing the door securely, or it pops open during cycles.
• Noticeable gaps or misalignment when the door is closed.
• Increased drying times, due to heat escaping.
• The dryer stops or pauses, triggered by door sensor issues.
• Visible wear or damage to the door or its components.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Baffle Washer is an OEM part for GE dryers. It works with the baffle screw to secure the dryer baffle in place on the drum. This washer helps to distribute the pressure and prevent the baffle from loosening or coming off during the drying cycle.

A bad washer can lead to issues with the baffle becoming loose or detached, causing uneven tumbling of the clothes or potential damage to the dryer drum. Causes of a bad part can include wear and tear over time, damage due to excessive vibration or movement, or improper installation.

Symptoms of a bad baffle washer include:

• Baffle becoming loose or detached from the dryer drum
• Clothes not tumbling evenly, resulting in uneven drying
• Unusual noises, such as rattling or banging, during operation
• Visible signs of damage or wear on the baffle screw washer

Replace your worn-out or damaged baffle washer with this genuine OEM GE part to ensure secure and smooth operation of the dryer baffle.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This Wi-Fi & Bluetooth control board restores wireless connectivity so your appliance can pair with smart devices and communicate with apps or hubs. It replaces a failed or unresponsive wireless module to re-enable remote monitoring and control. What it does:

• Provides Wi-Fi and Bluetooth radio functions for appliance app connectivity and smart features
• Enables remote diagnostics, notifications, and appliance-to-app communication when supported
• Replaces boards that show no wireless connection, intermittent pairing, or failed network registration
• Works as the appliance's primary wireless interface; does not include separate display or main control board functions

• One Wi-Fi & Bluetooth control board with instructions

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Follow manufacturer instructions for board handling and ESD-sensitive components
• Verify wiring harness connections and antenna leads are secured and routed per OEM guidance

8-18 hi/lo 5/8

This sensor rod harness connects a temperature sensor to the appliance wiring, restoring proper signal transmission for accurate temperature monitoring and control. It's a direct-fit replacement when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection between the sensor rod and the control board to transmit temperature readings.
• Replaces frayed, burned, or broken wiring that can cause intermittent or no temperature readings.
• Helps resolve symptoms such as erratic temperature control, long heating/cooling cycles, or fault codes related to sensor circuits.
• Maintains secure, insulated connections to prevent shorting or open circuits.

• One sensor rod harness.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Access may require removing panels or components; handle sensors and wiring gently to avoid damage.
• Verify connector orientation and secure clips fully; do not force connectors.