Gld3600l00bb Parts

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

Size: 10-32 GXTT FLP.595 S

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

Valve flapper for the washer's dual-pump drain assembly that directs water between pumps for proper draining. Replacing a worn or torn flapper helps restore drain operation and reduce leaks or poor drain performance. What it does:

• Directs water flow between the washer's dual drain pumps to ensure proper draining.
• Commonly linked to symptoms such as slow or incomplete draining, water remaining in the tub, or intermittent leaks.
• Replaces a cracked, torn, or hardened flapper that no longer seals or diverts flow correctly.

• Disconnect power and turn off water supply before beginning any repair.
• Access typically requires removing the washer's front or rear access panel and the drain pump assembly—use basic hand tools.
• Test drain function with a short cycle and check for leaks.

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

Replacement main control board and tactile board kit restores control and user input when the original electronics or buttons become unresponsive, helping return oven/range controls and display responsiveness. What it does:

• Primary control board: manages the appliance's electronic control functions and communicates with the user interface.
• Tactile board: provides the button interface so touch or press inputs register with the control module.
• Common symptoms addressed: unresponsive or intermittent buttons, unresponsive or blank display, or controls that do not respond reliably.
• Replaces both the main module and its associated keypad in one kit for a matched repair.

• Disconnect power at the breaker before starting any repair to avoid shock or injury.
• Handle circuit boards by the edges and avoid static discharge; use an ESD strap if available.
• Replacement typically requires removing the control panel and unplugging/reconnecting wiring harnesses; keep track of connector locations.

The GE screw is an OEM replacement part responsible for securing various components and parts of the dishwasher together. The screw is designed to provide a tight and secure connection for different panels, brackets, or other elements within the dishwasher. It plays a crucial role in maintaining the structural integrity of the appliance by preventing loose parts.

Common causes of a bad screw can include regular wear and tear from frequent use, exposure to moisture leading to corrosion, or damage from over-tightening. A compromised screw can result in loose or unstable components, which can affect the dishwasher's performance and safety.

Symptoms of a bad screw include:

• Loose or wobbly components within the dishwasher
• Difficulty in securing parts properly
• Visible rust or corrosion on the screw
• The screw head being stripped or damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

This dishwasher hose clamp secures a hose to its fitting to help prevent leaks. Replace a corroded or loose clamp to restore a tight, reliable seal at a hose connection point. What it does:

• Tightens around a dishwasher hose and fitting to maintain a watertight seal
• Helps resolve leaks at hose joints or beneath the unit
• Replaces clamps that are corroded, bent, stripped, or won't hold tension
• Symptoms include moisture at the connection, hose slipping off, or recurring leaks

• Includes 1 hose clamp

• Disconnect power at the breaker and shut off the water supply before servicing
• Access the affected hose connection and place a towel or pan to catch residual water
• Release and remove the old clamp; fully seat the hose, position the new clamp just behind the fitting's barb, and tighten/secure
• Run a short cycle and check for leaks at the connection

This suction ring sits in the dishwasher's sump/filter area and helps channel wash water into the circulation system. Replacing a worn ring can help restore proper water pickup and spray pressure for reliable cleaning performance.

• Helps maintain suction at the pump inlet for steady water flow to the wash system
• Supports proper spray arm rotation and wash coverage
• Common symptoms of failure: poor cleaning, weak spray, spray arms not turning consistently, or unusual noise from the sump area
• Wear or damage can disrupt circulation

• Disconnect power and water supply before servicing
• Remove the lower rack, then the lower spray arm and filter/sump cover to access the ring
• Note the ring's orientation; press the new ring fully into place before reassembly
• Run a short test cycle to ensure proper circulation

Specs: 8-18 ab tr 7/8 s

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening

A replacement 8-32 x 1/4 screw with an HXP-style head that secures panels, brackets and small appliance assemblies. Replacing stripped or missing screws restores proper fit and helps reduce rattling and loose parts. What it does:

• Fastens panels, brackets, grounding tabs and small components in appliance assemblies.
• Restores secure mounting when original screws are missing or damaged.
• Helps stop vibration-related noise and misaligned panels.
• Useful when reassembling parts after service or component replacement.

• Always disconnect power before working on electrical appliances.
• Use the correct driver for the HXP head to avoid stripping; do not force the screw.
• Tighten to hold parts snug—do not overtighten to avoid thread or part damage.
• Replace like-for-like; match thread size and head style to the original fastener.

Black