Gldt690tbb-00 Parts

The Lower Dishrack Stud and Roller Assembly is an OEM part for GE dishwashers. It is essential for the smooth operation of the dishwasher's lower dishrack, allowing it to slide in and out. This assembly includes the roller that attaches to the dishrack and the studs that secure these rollers in place.

Symptoms of a bad Lower Dishrack Stud and Roller Assembly include:

• The dishrack sticking or jamming when moved
• Rollers falling off or breaking
• Unusual noises when the dishrack is pulled in or out
• Difficulty in keeping the dishrack aligned within the dishwasher

Common causes for issues with the assembly often involve regular wear and tear, accumulation of detergent residues or food particles that can corrode or clog the rollers, and accidental damage from handling. If the rollers or studs are damaged, replacing them can greatly improve the functionality and longevity of your dishwasher.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher drain pump removes wastewater from the tub at the end of cycles, helping prevent standing water and ensuring proper draining performance. Replacing a failing pump restores efficient water removal and helps avoid wet dishes and odors.

• Pumps water out of the dishwasher to the household drain
• Common symptoms: won't drain or leaves water in the bottom, unusual humming/buzzing during drain, intermittent or slow draining
• Also helps if the pump is seized or electrically failed

• Disconnect power and turn off water before servicing
• Protect the floor from residual water; have towels or a shallow pan ready
• Access is typically from the bottom/front; transfer wiring and hose clamps to the new pump
• Ensure a clear, unkinked drain hose and a clear air gap or disposal inlet after installation

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Cylindrical filter that helps trap sediment and debris to protect your appliance's internal components and maintain water flow. Replacing a worn filter restores filtration and helps prevent clogging-related performance issues. What it does:

• Captures sediment and particulates to reduce debris reaching valves, pumps, and dispensers.
• Helps maintain consistent water flow by preventing buildup in flow paths.
• Reduces risk of clogs that can cause noisy operation or degraded performance.
• Common symptom: reduced water flow or visible particles in water/dispensed liquids.

• Turn off power to the appliance and shut off the water supply before starting.
• Relieve pressure and drain water from the lines where applicable to avoid spills.
• Inspect and replace any worn O-rings or seals; ensure the filter seats properly.
• After installation, restore power/water and run a short cycle or check for leaks.

This dishwasher microswitch is the snap-action switch used in the door-latch interlock. It signals the control when the latch is engaged so cycles start and continue only when the door is securely closed.

• Senses latch position and sends an open/closed signal to the control
• Failure signs include the cycle not starting, stopping when the door is bumped, or needing to press on the door/handle to run
• Restores reliable door-closed detection and safe operation
• Direct replacement for a worn, sticking, or inconsistent switch

• Disconnect power to the dishwasher before servicing
• Note wire positions (COM/NO/NC); transfer any actuator/lever or bracket from the original switch
• Ensure a positive "click" and correct continuity before reassembly
• Latch and strike alignment after installation

This pump hose and clamps create a sealed connection between the dishwasher's pump and internal plumbing. Replace when the hose is cracked or clamps are corroded/loose to stop leaks and restore a secure, watertight fit. What it does:

• Creates a sealed connection between the pump and internal plumbing
• Helps contain water flow during wash and drain operation
• Replace if the hose is cracked, brittle, swollen, or deformed
• Symptoms include water leaking under the dishwasher or loose/corroded clamps

• Disconnect power and water; pull the dishwasher forward as needed for access
• Expect residual water—protect flooring and have a towel or pan ready
• Remove old clamps and hose; fully seat the new hose on fittings, then position and secure clamps at the bead/ridge
• Run a brief cycle and check for leaks before reinstalling

Upper dishrack stop.

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

If looking for the two wheel guide rail bracket order WD12X10221

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged

A replacement black select button for the control console that restores a responsive, easy-to-use selector on compatible GE appliances. Replaces a cracked, worn or non-moving button so settings can be chosen reliably. What it does:

• Acts as the user-facing selector button on the control panel
• Allows selection of oven/cooktop or cycle options when pressed
• Fixes symptoms like a broken, stuck, loose or missing button
• Restores normal tactile feel and visual appearance of the console

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access may require removing the control panel or overlay—refer to your model's service instructions.
• Gently remove the old button and snap or press the replacement into place; avoid forcing it.

This hinge assembly secures and guides the appliance door, restoring smooth opening and reliable closure to prevent sagging or misalignment. Replace a worn or damaged hinge to reduce rubbing, binding, or uneven gaps. What it does:

• Supports the door pivot so the door opens and closes smoothly
• Keeps the door aligned to maintain a proper seal and prevent gaps
• Stops or reduces sagging, rubbing, or catching when the door moves
• Helps eliminate noise or binding caused by a worn hinge

• Turn off power and disconnect the appliance before starting any repair
• Support the door during removal and installation to avoid dropping or damage
• Use the OEM fasteners and torque to manufacturer recommendations when available