Gldt690tbb-00 Parts

This hinge assembly secures and guides the appliance door, restoring smooth opening and reliable closure to prevent sagging or misalignment. Replace a worn or damaged hinge to reduce rubbing, binding, or uneven gaps. What it does:

• Supports the door pivot so the door opens and closes smoothly
• Keeps the door aligned to maintain a proper seal and prevent gaps
• Stops or reduces sagging, rubbing, or catching when the door moves
• Helps eliminate noise or binding caused by a worn hinge

• Turn off power and disconnect the appliance before starting any repair
• Support the door during removal and installation to avoid dropping or damage
• Use the OEM fasteners and torque to manufacturer recommendations when available

This sprinkler nozzle directs wash water into a focused spray inside the dishwasher for effective coverage. Replacing a clogged or damaged nozzle restores proper spray pattern and helps improve cleaning results, especially on the upper rack.

• Channels water through the sprinkler assembly for targeted spray coverage
• Maintains the correct spray pattern and pressure for thorough washing
• Replace if clogged with mineral deposits, cracked, loose, or missing
• Symptoms can include poor cleaning, weak/uneven spray, or the upper rack not getting clean

• Disconnect power and water supply before servicing; allow the tub to cool
• Pull out the rack to access the sprinkler area; remove the old nozzle (snap or twist fit varies by model)
• Clean mating surfaces and install the new nozzle securely, ensuring proper alignment
• Run a short test cycle to verify normal spray operation

This sump gasket seals the dishwasher's sump to the tub to keep wash water contained. Replacing a worn or flattened gasket helps stop leaks and maintain proper wash and circulation performance.

• Creates a watertight seal between the sump/pump assembly and the tub bottom
• Helps prevent leaks onto the floor or into the base pan
• Maintains wash pressure and circulation by preventing air intrusion
• Replace if torn, cracked, deformed, or if water is leaking from the center/bottom of the unit

• Disconnect power and water before servicing; use gloves to protect from sharp edges
• Access the sump from inside the tub or underside (model dependent); remove spray arm/filter as needed and release the retaining ring or tabs
• Clean mating surfaces; install the new gasket evenly without twists and ensure proper orientation
• Reassemble and run a brief fill/wash to check for leaks before fully reinstalling

The Spray Arm Connector Assembly is an OEM replacement part for GE dishwashers. This assembly connects the upper and lower spray arms to the water inlet valve, allowing water to flow through the spray arms during the wash cycle. 

Symptoms of a bad spray arm connector assembly include: 

• Uneven or inconsistent water coverage on dishes
• Clogged or kinked spray arm assemblies 
• Leaks at the tub connections
• Reduced water pressure impact 

Causes of a bad spray arm connector assembly can be mineral buildup affecting water flow, cracked or damaged connectors, or wear over time.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Pressure switch that monitors water level and signals the washer control board when to start or stop filling. Replacing a failing pressure switch can help restore correct fill levels and normal cycle operation. What it does:

• Senses air pressure from the tub and tells the control when the correct water level is reached
• Stops the fill valve once the desired level is detected to prevent overfilling
• Can cause underfilling, overfilling, or failure to advance cycles when faulty
• Works with the washer's control system to ensure proper fill and cycle progression

• Disconnect power to the appliance before starting any repair
• Shut off water supply and relieve any trapped water before accessing components
• Carefully disconnect wiring harness and air tube; note routing for reassembly

This replacement door lock hook secures the appliance door latch assembly so the door stays closed during cycles, preventing interruptions and ensuring proper operation. Fits into the door/latch mechanism to engage the lock. What it does:

• Captures and holds the door strike so the door remains firmly closed during operation
• Helps the door lock switch engage properly to allow cycle start and prevent mid-cycle door openings
• Commonly replaced when the door won't stay closed, the latch feels loose, or the door intermittently unlocks
• Works as the mechanical mating piece for the door lock assembly

• Disconnect power and water before starting any repair
• Requires access to the door/latch area—some disassembly of the door or console could be needed
• Use basic hand tools and keep track of fasteners; avoid forcing plastic tabs to prevent breakage

This right switch breakwater helps position and protect the dryer control switch assembly, keeping the switch secure and preventing rubbing or shorting. It restores stable switch alignment for reliable control operation. What it does:

• Holds the right control switch in place to prevent movement and wear
• Protects the switch from contact with adjacent components that can cause sticking or intermittent operation
• Helps stop rattling or vibration-related noise from the control area
• Supports proper button/knob actuation for consistent user input

• One right switch breakwater

• Intended for use in the dryer control area; inspect surrounding parts for related damage
• Disconnect power before servicing to avoid shock or accidental startup
• Use basic hand tools; do not overtighten fasteners to avoid cracking the plastic
• Replace damaged switches or mounting hardware together for best results