Glwn2800dws Parts

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

This front panel assembly replaces a cracked, worn or damaged console face to restore your appliance's appearance and support the control components. It provides the outer housing for buttons, displays and mounting points. What it does

• Covers and protects the control area from spills, dust and impact.
• Provides mounting locations and alignment for buttons, switches and display components.
• Restores a secure, finished surface when the original panel is cracked, warped or missing.
• Resolves cosmetic issues and loose or misaligned controls that affect operation.

• One panel front assembly.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Remove any trim, bezels or clips carefully to avoid damaging adjacent parts; keep fasteners for reinstallation.
• Handle edges and mounting tabs gently; some panels use plastic clips that can break if forced.
• If the control components or display must be transferred, note connector locations and orientation before disconnecting.

A replacement door counterweight that restores proper balance so doors and drawers open and close smoothly. Helps reduce sagging and uneven alignment for safer, quieter operation. What it does

• Adds weight to a door or drawer to maintain proper balance and alignment
• Helps prevent door sag, sticking, or uneven closing
• Reduces stress on hinges and tracks that can cause premature wear
• Can improve seal engagement and reduce rattling or vibration

• One counterweight

• Disconnect power to the appliance before starting any repair
• Support the door or drawer while removing fasteners to prevent dropping
• Use basic hand tools; follow the appliance service manual for specific steps

Size: 1/4 - 20 b.

This left-hand end cap is a direct-fit replacement part that helps secure the washer's left-side assembly and restores proper cabinet/drum alignment for smoother operation and reduced vibration. What it does:

• Caps and protects the left-side end of the washer assembly to prevent wear and debris entry
• Helps maintain proper alignment of the washer drum/cabinet on the left side
• Reduces noise, rubbing, or wobbling caused by a damaged or missing end cap
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power and water to the washer before starting any repair
• Basic hand tools may be required; some disassembly of the cabinet or front panel could be needed
• Inspect adjacent components (gaskets, seals, fasteners) for wear while replacing the end cap

This replacement backsplash assembly restores the finished vertical panel behind your range or cooktop, protecting the wall and concealing control components for a like-new appearance. Made to match the original fit and finish. What it does:

• Replaces a cracked, dented, chipped or warped backsplash panel
• Protects the wall from splashes, grease and heat around the cooking surface
• Conceals and supports control housing and wiring on compatible models
• Restores proper alignment and appearance after damage or wear

• Designed to install with the original mounting screws and brackets; retain existing hardware unless replacements are specified
• Disconnect power to the appliance before beginning work to avoid electrical shock when removing control or wiring covers
• Handle carefully to avoid scratching the painted finish; two-person lift may be needed for larger units
• If the part attaches to control components, secure all fasteners before restoring power

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.