Gne22gmebfs Parts

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

I received the item quickly and installed it the same day.There were only 2 screws to secure it to the rail rack. Read more

Changed fan motor, rubber grommets, and dust cover. It sounded like the vibrating sound was being caused by the motor. But, come to find out I had a chipped blade on one of the fan blades. So make sure and check the fan blade first. Thanks Appliance Parts Pros everything for just as it should. Read more

Order new parts to replace the broken ones. Read more

I had found that the fan in the freezer was making a lot of noise. Turns out the shaft was loose, causing the flan blade to wobble. Replaced the motor and fan and now it runs like a new unit. Read more

After changing water filter, flow came to a stop. Would chatter without any water. Confirmed I had flow from the wall supply to the fridge as I broke the water line at the union and let run into a bucket. Then I removed the water filter housing and tube assembly after reconnecting supply. Now the water was only circulating from the wall to the filter housing to the bucket. No flow and chatter was present. I did this to rule out a frozen reservoir. Really simple fix. Was able to remove... Read more

Went online and looked for a parts dealer using the refrigerator model number. Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

Ordered a new mother board install was easy and everything is working great. Web site was easy to navigate . Part came in one day.Thank you Read more

This fridge has had a problem of ice building up around evaporator coil in fresh food side. Wife (she HATES this thing) says it's done this from day one; 10 years. GE guy says all these models do this and there's no fix for it, so we have clean out the ice periodically... Like the 1940s pre auto defrost. Now with the issue of FF side temp too highi assumed the ice had built up around FF evaporator coil preventing proper cooling, but AppliancePartsPros.com suggested the FF temp thermistor may... Read more

Determined that the evaporator fan in the freezer compartment was not running properly and making noise. Ordered a replacement evaporator fan and blade. Removed the freezer door, baskets, and side rails. Removed the back panel of the freezer compartment by unscrewing and disconnecting the power cable connected to the fan. Removed fan blade. Turned over the panel and removed the back fan bracket and fan. Installed replacement fan, back fan bracket, and fan blade. The grommets ordered were the... Read more

I ordered the parts & installed the handle. Read more

Removed two side screws took handle off and put the new handle on and replaced screws. Read more

Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more