Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.
First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more
Captures lint and debris during drying to prevent exhaust buildup and fire hazards. Replace when torn, ripped, or damaged. Confirm fit with your model.
Remove old lint catcher, install the new one. Read more
Dryer bearing slides enable smooth drum rotation. Replace when hearing squeaking or rumbling sounds during cycles. Confirm fit with your model number.
A thumping sound (like sneakers in the dryer) started happening. We stopped using it so that it wouldn't get worse and potentially break more parts. Online research suggested rear drive shaft would be the problem. But also suggested while we have the dryer apart, would be smart to replace the belt and the slides/glides (green and white plastic tabs in front, attached to the door). We ordered all the parts from AppliancePartsPros.com and they arrived FAST. It helps to have two people for this... Read more
Control knob that mounts on the timer shaft to select drying times and cycles. Replace if cracked, broken, or won't grip the shaft properly. Includes clip.
This was by far the EASIEST repair I have ever done. All I had to do was remove the broken knob, the back panel and disconnect the old timer. I then connected the new, put it in place, and replaced the knob. After a test run, I put the panel back on and have been doing laundry since! Read more
Seals the gap between the drum and front panel to prevent air leaks and noise. Replace if worn, damaged, or causing squeaking sounds. Verify fit with your model.
Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more
Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.
I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more
The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.
Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
If your dryer timer won't engage or the knob turns freely without starting cycles, this timer controls cycle duration. Simple 20-minute DIY repair.
Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more
Dryer won't advance through cycles or stops mid-cycle? The timer controls cycle duration and progression. Moderate DIY repair with basic tools.
The selector knob and timer quit working on our GE dryer. We noticed the plastic selector knob was cracked inside when we pulled it off. We decided to order a new timer along with the selector knob just in case the new knob didn't solve the problem. We put on the new knob as easy as we pulled it off and the dryer would turn on again, however it was not going off in the selected amount of time it was supposed to. So it turns out we did need the timer part as well. These parts came in the... Read more
Unusual noises or vibrations during the drying cycle Causes of a faulty lint chute assembly can include normal wear and tear over time, clogging due to excessive lint accumulation, or physical damage due to improper cleaning or maintenance. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.
Replaced front panel and inner liner of door (kit), trap duct assembly, both bearing slides (gray and white), and drum front support bearing. Procedure is pretty much what one sees in the video clips. Exceptions in our case included: 1. The fact that our door latch¹ was on the front panel while the door strike² was on the door. The newer (replacement) design has the latch on the door and the strike on the front panel! 2. The new door did NOT have the door latch installed (as shown in the... Read more
Supports and stabilizes the dryer drum for smooth rotation. Replace if shaft is worn, bearing is damaged, or drum wobbles or sinks at the rear.
I replaced the slide bearings a few years back. A few months later the rear bearing started to go so I replaced that one. Bad idea. Replace these two at the same time. The wobbling from the rear bearing failure caused accelerated wear on the slide bearings. Without the money to fix it I ran it as it was. Another bad idea. The drum not only chewed through the slide bearings, but eventually the assembly as well. I replaced the whole assembly and rear bearing at one time a couple days ago. It was... Read more
Illuminates your dryer drum for better visibility when loading and unloading clothes. Replace when burned out or flickering. Verify fit with your model.
It was an easy repair just screwed in. The ordering process and simple no hassle and got here fast! I will definitely order from you again Read more
Fix a dryer that won't advance cycles or stops mid-cycle with this timer control assembly. Easy DIY repair with simple panel removal in under an hour.
After taking the timer apart to see why it would not turn I found the timer motor was jammed. Taking the motor apart I found a broken gear. Looked up the model number of the dryer and found a new timer assembly thru appliancepartspros.com I ordered, a very easy process, received the part 2 days later. Installed the assembly in about 5minutes and had the dryer back up and running Read more
Captures lint and debris to maintain airflow and drying efficiency. Replace if cracked, torn, melted, or warped. Confirm fit using your model number.
I ordered the new filter on one day and it was delivered the next. Other web sites told me the part was no longer available and I was very surprised and pleased that Appliance Parts Pros had it in stock and shipped it so promptly. Thank you. Read more
Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.
First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more
Control panel knob for selecting wash cycles. Replaces broken, cracked, or stripped knobs. Installs on the front panel—simply pull off the old knob.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.