Gtdb300 Parts

This replacement cycle selector knob restores the washer's cycle control so you can easily choose wash settings. It provides a secure, easy-to-grip interface when the original knob is cracked, stripped, or missing. What it does:

• Replaces a worn, cracked, or loose cycle selector knob so the control dial turns smoothly
• Engages the console or timer shaft splines to allow selection of wash cycles
• Helps resolve symptoms like a spinning or slipping knob, inability to change cycles, or a missing knob
• Matches OEM fit and function for a direct-replacement installation

What's included:

• One cycle selector knob

Install notes:

• Disconnect power (unplug or switch off the breaker) before starting any repair
• Align the knob splines with the control shaft and push firmly until seated; some models require removing the control console bezel first
• If the knob does not seat easily, inspect the shaft splines and control for damage before forcing

Fix a dryer that won't change cycles or start with this rotary selector switch. Solves control issues from wear or electrical problems. Moderate DIY.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

Replacement strain relief bracket that secures the power cord at entry point. Needed when bracket is cracked, broken, or missing to restore safe cord routing.

This is the top cover panel for a high-depth dryer model. It forms the outer top surface of the dryer cabinet, providing structural support and a finished appearance. Replace this panel if it is dented, rusted, warped, or damaged, which can affect the dryer's alignment and seal.

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

This knob assembly replaces a worn, broken, or missing control knob so you can reliably select heat or settings on your range or cooktop. It restores safe, accurate user control and a finished appearance. What it does:

• Fits onto the control shaft to allow turning the switch for burner/oven settings
• Restores tactile grip and clear position selection when the original had stripped or cracked
• Helps stop slipping or intermittently losing contact between the user and the control
• Suitable for use where the original knob assembly is damaged or missing

• Disconnect power (or turn off gas appliance supply) before servicing controls.
• Push the knob straight onto the control shaft until fully seated; pull straight off to remove.
• Inspect the switch/shaft for damage; replace the switch or shaft if the knob does not seat securely.

Fix buzzing noises or no flame in your gas dryer with a new valve assembly. Solves igniter glow without ignition. Moderate DIY repair with basic tools.

Is your dryer overheating or taking too long to dry? A damaged exhaust duct restricts airflow. This vent connector restores proper ventilation.

Fixes dryer not heating or insufficient heat issues. Complete gas valve and burner assembly regulates gas flow for consistent drying. Moderate difficulty.

Replacement rear panel for dryers. Restores the cabinet's back surface when the original is dented, rusted, cracked, or damaged. Secures and protects internal wiring and components.

Housing cover that protects and encloses the dryer heating element assembly. Replace if cracked, broken, or damaged to restore proper dryer operation.

Fix electrical grounding issues with this dryer ground strap assembly. Restores proper chassis grounding to reduce shock risk. Simple repair for worn connections.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.