Gte181shdrss Parts

This freezer door gasket restores a tight, energy-saving seal between the freezer door and the cabinet. Replacing a worn or misshapen gasket helps stop air leaks that cause frost, moisture, and temperature fluctuations. What it does:

• Seals the perimeter of the freezer door to keep cold air in and warm air out
• Helps maintain proper freezer temperature and reduce energy waste
• Limits frost/ice buildup and condensation around the door opening
• Replaces gaskets that are torn, brittle, warped, or won't seal properly

• 1 dark gray freezer door gasket

• Disconnect power before servicing
• Unpack and lay the gasket flat; warm gently (hair dryer on low or warm water) to relax folds
• Clean and dry the door surface and gasket channel
• Press the gasket lip fully into the groove, ensuring corners seat evenly; close the door and check for uniform contact

This factory screw secures brackets, panels, and internal components so assemblies stay tight and aligned. Replace a missing or damaged fastener to eliminate rattles, looseness, and misaligned parts. What it does:

• Fastens components, panels, hinges, or brackets to the appliance frame
• Helps maintain proper alignment and a solid, rattle-free fit
• Replaces stripped, rusted, or missing hardware
• Can address vibration noises and loose assemblies

• Includes 1 screw

• Unplug the appliance and shut off water before servicing
• Wear gloves; sheet-metal edges can be sharp
• Start threads by hand to avoid cross-threading; use the appropriate driver
• Tighten snugly—do not overtighten to prevent stripping

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation

This center hinge pin is the pivot shaft for the door at the middle hinge on select refrigerators. Replacing a worn or bent pin restores proper door alignment and smooth movement to help the door close and seal correctly.

• Serves as the door's pivot on the center hinge
• Maintains correct door height and alignment
• Helps the door open and close smoothly without binding
• Common symptoms: door sagging or rubbing, squeaking, wobbling, or not closing fully/popping open

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door before removing the center hinge bracket fasteners
• Install the new pin on the center hinge; reuse original spacers/bushings in their original order
• Reassemble, then check door alignment and gasket contact; adjust the hinge as needed per your model

This center hinge supports and pivots the refrigerator door at the middle of the cabinet. Replacing a bent or worn hinge restores smooth door movement and a reliable seal to help maintain proper temperatures.

• Supports door weight and provides the center pivot for opening and closing
• Helps maintain door alignment for even gasket contact
• Wear or damage can cause sagging, rubbing, squeaks, or doors that won't close/seal
• Visible bending, looseness, or a damaged hinge bracket/pin indicates replacement is needed

• Disconnect power and remove items from the door to reduce weight
• Support the door and have a second person assist; note the order of any spacers/washers
• Remove mounting screws, replace the hinge, and reinstall while keeping the door square
• Verify the door swings freely and the gasket seals evenly; adjust alignment as needed

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This leveling leg supports and stabilizes the refrigerator cabinet. Adjusting it keeps the unit level so doors align and seal correctly, helping reduce vibration and noise for smoother, more reliable performance.

• Threads into the base to support and level the appliance
• Allows height adjustment for proper door alignment and gasket contact
• Helps reduce rocking, vibration, and rattling noises
• Resolve issues like doors not closing fully, uneven gaps, or a wobbly cabinet

• Disconnect power and move the appliance carefully to access the leg
• Use a helper and protect flooring; tip the unit slightly and support it securely
• Unthread the old leg; hand-thread the new leg, then adjust as needed with a wrench
• Level front-to-back and side-to-side; avoid cross-threading or overtightening

The Control Housing is an OEM component specifically designed for GE refrigerators. It contains and protects all electronic control boards that operate refrigerator functions.

Located within the refrigerator interior, the housing provides both physical shielding and proper ventilation around sensitive electronic components. This helps maintain trouble-free performance under various interior temperature conditions.

Symptoms of a bad control housing include:

• Refrigerator functions becoming intermittent or unresponsive
• Control boards overheating and triggering error codes  
• Physical damage, cracks, or improper fit of the housing
• Difficulty accessing boards for diagnosis and service  

Causes relate to physical impact, interior moisture exposure over time, or failed ventilation of the enclosed space. 

This genuine OEM GE replacement is also compatible with Hotpoint, RCA, or Kenmore models.

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

This compressor start relay and overload is the start device for your refrigerator's compressor. It helps the motor start and protects it from overheating, supporting reliable operation when the original start components fail.

• Provides the initial boost to start the compressor via a PTC start relay
• Overload protector opens the circuit if temperature or current is excessive
• Common symptoms: compressor won't start and repeatedly clicks
• Warm or rising fresh food/freezer temperatures
• Compressor starts then stops after a few seconds

• Disconnect power and allow the compressor to cool before servicing
• Access the compressor compartment; note wire locations and device orientation
• Pull the old device straight off the compressor pins; press the new assembly fully onto the terminals and reconnect wires securely
• Inspect connectors for heat damage and replace any burned terminals before restoring power

This top hinge and pin assembly supports the refrigerator door at the upper corner and provides the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and a consistent, reliable door seal.

• Supports door weight at the top and provides the pivot for smooth swing
• Maintains door alignment to prevent rubbing and uneven gaps
• Helps the door close securely for proper gasket contact
• Typical symptoms: door sags or scrapes, doesn't close flush, binds/clicks at the top, visible wobble

• Disconnect power and remove items from the door shelves
• Have a helper support the door; remove the top hinge cover and mounting screws, then lift the door straight up/off
• Position the new hinge, secure with the original hardware, and set the door back on the pins
• Adjust leveling if needed before restoring power

The Control Knob is an OEM part for GE refrigerators. This knob is responsible for adjusting and controlling various settings on your refrigerator, such as temperature or function selection.

A bad control knob can be caused by normal wear and tear, accidental damage, or a malfunctioning internal mechanism. If you experience difficulties in accurately adjusting or selecting the desired settings on your refrigerator, it may be time to replace the control knob.

Symptoms of a bad control knob include:

• The knob feels loose or wobbly when turned
• Inaccurate temperature adjustments
• The knob gets stuck or does not turn smoothly
• The knob is cracked, broken, or missing

Replace your faulty control knob with this genuine OEM part to restore your refrigerator. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This control knob fits onto the refrigerator's control shaft so you can turn and set temperature or other settings. Replace a cracked, stripped, or missing knob to restore smooth operation and reliable adjustments.

• Connects to the control shaft to adjust temperature or feature settings
• Provides a secure, correct fit to prevent slipping or free-spinning
• Restores the ability to set and read the desired level
• Common symptoms: broken/cracked knob, knob won't stay on, spins freely, can't change settings

• Disconnect power to the refrigerator before servicing
• Pull the old knob straight off; gently wiggle if needed—avoid prying on the panel
• Align the flat/D-shaped opening with the control shaft and press on until fully seated
• Turn the control to verify smooth operation and proper alignment with markings

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This is a half-width cantilever shelf for the refrigerator's fresh food compartment. It mounts on the rear wall rails to create adjustable storage space and replace a cracked, sagging, or missing half shelf.

• Provides adjustable storage; hangs from rear wall tracks
• Replaces a shelf that is cracked, warped, unstable, or missing
• Helps restore proper organization and usable space
• Maintains correct fit and support for refrigerated items

• Unplug the refrigerator and remove food from the area before starting
• Lift and slide the old shelf out of the wall rails; install the new shelf into the same slots
• Inspect wall rails and supports for damage before reuse
• Handle carefully to avoid chipping edges or scratching liners