Gtw180ssjww Parts

Size: 8-18 b.

The Triple Water Valve is an OEM part for GE washing machines. This part controls the flow of water into the washer, allowing for the precise mixing of hot, cold, and warm water necessary for different wash cycles.  

Causes of a bad triple water valve can include mineral buildup or blockages from debris, electrical issues such as faulty solenoids, and wear and tear from frequent use.  

Symptoms of a bad triple water valve include:

• The washer not filling with water or filling very slowly
• Incorrect water temperature during wash cycles
• Leaks from the valve area
• The washer not advancing through cycles properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This knob and clip assembly secures a range or cooktop control knob to the control shaft so the knob turns the valve or switch reliably. It restores firm, responsive control and prevents the knob from slipping. What it does:

• Secures the control knob to the shaft so knob rotation moves the underlying valve or switch
• Prevents the knob from wobbling, spinning freely, or falling off during use
• Re-establishes positive engagement for accurate temperature or burner selection
• Compatible with common plastic control knobs that use a clip-style retention

• One knob and clip assembly as shown

• Disconnect power to the appliance before starting electrical work; for gas appliances, shut off the gas supply per the appliance manuals
• Remove the existing knob (pull straight off) and replace the clip and knob; use gentle pressure to avoid breaking plastic parts
• If the knob is tight after installation, ensure the clip is fully seated on the shaft and aligned with the knob hub

This tub clamp secures the washer tub or associated hoses to keep components aligned and sealed during operation. It replaces a worn or broken clamp to reduce movement and help prevent leaks and noise. What it does:

• Holds the tub/hose connection or tub assembly parts together to maintain a tight fit
• Helps prevent leaks caused by loose or damaged clamps
• Reduces rubbing, vibration, and associated noise from a loose tub assembly
• Restores proper component alignment after clamp failure

• Disconnect power and turn off water supply before starting any repair
• Inspect mating parts (tub, hoses, mounting points) for damage and clean before installing
• Use appropriate clamp pliers or screwdriver as required; ensure clamp is seated and tightened evenly

5/16-18 tpt ihw s n

A small push-in plug button used to fill or cover an access hole or trim opening and restore a finished appearance. Designed to snap into place for a secure fit and to keep dirt and moisture out. What it does:

• Covers unused holes or fastener openings to restore a finished look
• Helps keep dirt, moisture, and debris from entering cavities
• Holds trim or panels flush by filling gaps where a fastener or post is missing
• Commonly replaced when cracked, lost, loose, or causing rattles or gaps

• One plug button

• Disconnect power to the appliance before accessing panels or trim
• Typically snaps into place—press firmly until seated; may require removing trim for access
• Avoid prying with sharp tools that can damage surrounding surfaces
• Replace only with the exact part number to ensure proper fit and finish

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

This front panel assembly replaces a cracked, worn or damaged console face to restore your appliance's appearance and support the control components. It provides the outer housing for buttons, displays and mounting points. What it does

• Covers and protects the control area from spills, dust and impact.
• Provides mounting locations and alignment for buttons, switches and display components.
• Restores a secure, finished surface when the original panel is cracked, warped or missing.
• Resolves cosmetic issues and loose or misaligned controls that affect operation.

• One panel front assembly.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Remove any trim, bezels or clips carefully to avoid damaging adjacent parts; keep fasteners for reinstallation.
• Handle edges and mounting tabs gently; some panels use plastic clips that can break if forced.
• If the control components or display must be transferred, note connector locations and orientation before disconnecting.

A replacement door counterweight that restores proper balance so doors and drawers open and close smoothly. Helps reduce sagging and uneven alignment for safer, quieter operation. What it does

• Adds weight to a door or drawer to maintain proper balance and alignment
• Helps prevent door sag, sticking, or uneven closing
• Reduces stress on hinges and tracks that can cause premature wear
• Can improve seal engagement and reduce rattling or vibration

• One counterweight

• Disconnect power to the appliance before starting any repair
• Support the door or drawer while removing fasteners to prevent dropping
• Use basic hand tools; follow the appliance service manual for specific steps

Size: 1/4 - 20 b.