Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a washer that won't start or has a blinking lid lock light with this lid lock wiring harness. Connects the lid lock to the control board. Easy DIY fix.
How the directions showed me. It was very easy. Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Fix washer leaking during drain cycle with this drain pump seal. Prevents water leaks between pump and tub. Easy DIY repair, takes about 30 minutes.
I replaced the drain pump and replaced the belt while I was under there since I noticed some shreds on the ground when I was investigating the problem originally. I am a girl and it was fairly easy to diagnose. I found the codes listed on the paper that’s taped inside the washer. There’s a service mode I was able to enter and that opened up the test mode. Every test was successful except for the drain test. So I entered my model on this site and was able to find the parts I needed Read more
Washer won't start or shows lid error? The lid lock bezel secures your lock mechanism. Simple press-in installation takes 25-30 minutes to restore function.
Noticed that lid lock light was not on, googled problem, ordered parts, working on 3rd day. Read more
Suspension rod and spring assembly for top-load washers. Mounts between tub and cabinet to absorb vibration. Replace if cracked, broken, or corroded.
I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more
Seals refrigerator door to keep cold air in and warm air out. Replace if cracked, torn, or door won't seal properly. Verify fit with your model number.
Replaced the door gasket. tip: No need to remove all the screws completely - loosen until you can peel off the old gasket. Read more
Washer won't advance through cycles or stops mid-wash? This timer control assembly manages fill, agitate, rinse, and spin sequences. 15-30 minute repair.
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy! Read more
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
The Triple Water Valve is an OEM part for GE washing machines. This part controls the flow of water into the washer, allowing for the precise mixing of hot, cold, and warm water necessary for different wash cycles.
Causes of a bad triple water valve can include mineral buildup or blockages from debris, electrical issues such as faulty solenoids, and wear and tear from frequent use.
Symptoms of a bad triple water valve include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ordered water inlet valve. Took all about 10 mins to change it solved the problem. Easy fix Read more
Fix washer shaking violently during spin cycle with this suspension rod upper ball joint. Common cause of unbalanced loads. DIY repair in 45 minutes.
I replaced all four upper ball joints and all four rod and spring assemblies. The washer loads now remain balanced during the spin cycle even with bulky items such as a kings sized blanket and a sheet and pillow set. I did the repair myself in less than 45 minutes total. This saved me from having to purchase a new washer. Read more
The Rotary Knob is an OEM replacement part for GE or Hotpoint washing machines. It provides the interface for selecting wash cycles and adjusting settings like temperature and spin speed. Causes of a bad rotary knob include cracking, peeling, or damage to labeling from repeated use over time. The internal mechanisms can also wear out, preventing proper rotation. Symptoms of a bad rotary knob are:
It is also compatible with RCA, Westinghouse, Tappan, and some Kenmore models.
Opened back up. Saw aQR code. Made the finding the parts easy Read more
The GE screw is an OEM replacement part responsible for securing various components or parts together on a washing machine. Its main function is to connect and hold together various parts, panels, or brackets, ensuring that they remain securely in place during the appliance's operation. The screw comes in the size 1/4-20 MCH HXW 5/8 S, indicating its thread size, head type, and length.
This part fixes the following symptoms:
The GE washing machine screw can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more
This shaft and tube assembly supports and drives the washer's inner basket during the spin cycle. Replacing a worn or bent assembly restores smooth rotation and helps reduce noise, vibration, and basket wobble.
After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements. This part fixes the following symptoms:
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.