Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The washer start stop switch button is the physical push button on your washing machine's control panel that signals the machine to begin or pause a cycle. It connects to the underlying switch mechanism that sends an electrical signal to the control system. Replace this part when pressing the button does nothing, the button feels mushy or broken, or the washer will not start or stop responding to that control.
All I had to do was remove 3, 1/4" screws from the back and take the front off. Two 5/16th screws hold the circuit board in place, remove them and press the button into the hole from the back. Replace the circuit board, slide the front back on and install the three 1/4" screws. Always unplug the washer first! Read more
Suspension rod and spring assembly that supports and stabilizes the washer tub. Replace if rod is broken, spring is worn, or assembly is damaged or missing.
I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Suspension rod and spring assembly for top-load washers. Mounts between tub and cabinet to absorb vibration. Replace if cracked, broken, or corroded.
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Fix no hot water, leaking when washer is off, or weak water pressure. This triple water inlet valve controls hot, cold, and warm water flow. DIY-friendly repair.
Replaced solenoid valve. Repair summary: Turn off H/C water supply, disconnect hoses. Unscrew 3 screws rear of main panel. Slide front panel laterally then pull up to remove. Unscrew 2 screws on solenoid valve part. Disconnect spade electrical connectors and remove defective part. Insert new part and do everything I just said in reverse. It was so easy a drunken monkey could have done it. Read more
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
The Mode Shifter & Shaft Assembly is an OEM replacement part for GE washing machines. It is a mechanical component located inside the washer tub that allows for shifting between agitation, spin, and other cycles. The mode shifter and shaft assembly receive input from the control system to precisely change the operational mode at designated points in the cycle. Causes of a bad mode shifter & shaft assembly include worn out or damaged internal gears, stripped or broken shafts, or a loss of integrity in components that restrict smooth shifting between modes. Symptoms of a bad mode shifter & shaft assembly include:
This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.
The GE screw is an OEM replacement part responsible for securing various components or parts together on a washing machine. Its main function is to connect and hold together various parts, panels, or brackets, ensuring that they remain securely in place during the appliance's operation. The screw comes in the size 1/4-20 MCH HXW 5/8 S, indicating its thread size, head type, and length.
This part fixes the following symptoms:
The GE washing machine screw can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more
This shaft and tube assembly supports and drives the washer's inner basket during the spin cycle. Replacing a worn or bent assembly restores smooth rotation and helps reduce noise, vibration, and basket wobble.
After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more
Fix water leaking from the top of your washer or spraying everywhere. This funnel shower head assembly disperses water evenly. Moderate DIY repair.
The Youtube videos made the process much easier to tear down the washing machine to replace these parts. These parts were easy to replace once the outside lid and control panel were removed. The initial component replaced was the hot/cold valve. It was leaking causing a continuous drip into the bowl. The Valve is attached to the funnel shower head asm. Best to replace all three parts at the same time or you may also create a leaking funnel shower head hose while replacing the hot/cold... Read more
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
Suspension rod and spring assembly for washing machines. Installs between the tub and cabinet frame. Replace when cracked, broken, or worn to restore stability.
I shopped around a bit - found one retailer that only had 1 shock in stock, another that only stocked the front shocks, etc. There is definitely a difference in the springs between the green colored and white colored shocks! I've torn this washer down before, so I'm fairly familiar with how it's put together. I've seen some of the You-tube videos on replacing this item, and some of the videos show far more disassembly than is required. I only removed the front, top, and controls, and... Read more
Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.
Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.