Gu1200xtkbo Parts

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks

Also suggested to order vent gasket WP8269259.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This standpipe houses the washer's overfill control and directs excess water into the drain path, helping prevent overfilling and internal flooding. It's a direct-fit replacement for the factory overfill control housing. What it does:

• Provides the sealed channel for excess wash water to flow to the drain
• Supports and locates the overfill/level control assembly
• Helps stop water from overflowing the tub and causing leaks
• Can resolve symptoms like unexplained overfilling, water leaking at the washer base, or fill-level issues

• Disconnect power and shut off water before starting any repair
• Access may require removing the washer top or control housing
• Inspect surrounding gaskets and hoses for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; test operation after reassembly

A threaded screw used to secure appliance components where an 8-16 thread is specified. Provides a straightforward replacement fastener to restore original fit and keep panels, brackets, and internal parts held securely. What it does:

• Fastens panels, brackets, trim, and small assemblies that use an 8-16 threaded fastener.
• Replaces missing, corroded, stripped, or damaged screws to stop rattling, gaps, or loose parts.
• Restores reliable mechanical connection after service or part replacement.
• Compatible where the OEM specifies an 8-16 screw for mounting or securing components.

• Use the correct driver to avoid stripping the head; start threads by hand to prevent cross-threading.
• Tighten until secure but avoid over-tightening to prevent damage to mounting holes or plastic parts.
• If working near electrical components, disconnect power and follow all safety precautions.
• Inspect mating threads and replace if damaged before installing this screw.

Also suggested to order vent gasket WP8269259.

This sump tab secures the dishwasher's sump assembly to the tub opening, keeping it properly aligned and sealed. Replace a broken or missing tab to address movement, rattling, or leaks originating from the sump area.

• Locks the sump assembly to the tub/base opening
• Helps maintain the sump-to-tub seal to limit leaks
• Keeps the pump intake and fine filter area properly positioned
• Common symptoms: leaks under the unit, loose/shifted sump or filter, rattling/vibration from the sump area

• Disconnect power and water supply before servicing
• Access the sump per your model (from inside the tub by removing lower rack/filters, or from below after removing the toe panel)
• Ensure the sump and gasket are fully seated; install the new tab until it locks securely
• Run a brief fill/drain test and check for leaks before reassembly

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This is a genuine 4-24 x 3/8 screw used to fasten trim and components on compatible appliance assemblies. It provides a secure, vibration-resistant connection so panels and parts stay properly aligned during use. What it does:

• Secures panels, brackets, or components to the appliance frame
• Helps prevent rattling or loosening from normal vibration
• Works with threaded or self-tapping holes sized for a #4-24 fastener
• Common replacement for stripped, rusted, or missing mounting screws

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread damage
• Replace any corroded or damaged screws in sets when multiple fasteners show wear
• Disconnect power and follow appliance safety guidance before servicing