Gu2455xtstd Parts

This is the exterior-facing panel that forms the visible front surface of the dishwasher door. It provides a finished appearance and helps protect the internal door components, including insulation and wiring. Replace this panel if it is dented, scratched, rusted, or if the finish has deteriorated significantly.

This is a rack adjuster mechanism that allows you to raise or lower the upper dish rack in your dishwasher. It attaches to the side rail and enables height adjustment to accommodate taller items on the lower rack. Replace it if the upper rack tilts, sags to one side, or the adjuster no longer locks into position.

White toe panel that covers the bottom front of your dishwasher. Replace if cracked, discolored, or missing to restore a finished appearance.

Right-hand door hinge that restores proper door alignment and smooth operation. Replace if your dishwasher door sags, binds, or won't stay open. Verify fit.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Access panel covers the base of your dishwasher, concealing wiring and mechanisms. Replace if cracked, broken, or missing after installation.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.

Fix water leaking from under your dishwasher with this pump volute. Directs water flow and prevents leaks with integrated seal. 20-minute repair.

This replacement screw fastens appliance components such as panels, brackets, or trim. Use it to replace a missing, stripped, or rusty fastener and restore a secure, rattle-free fit in your appliance assemblies.

• Secures panels, brackets, or hardware to maintain proper alignment
• Helps eliminate vibration, rattling, or loose-feeling parts
• Replaces fasteners that are missing, corroded, or cross-threaded
• Typical signs you need it: loose handle or panel, gaps, or hardware that won't stay tight

• Disconnect power (and shut off gas, if applicable) before servicing
• Match thread type and length to the original fastener for proper fit
• Start threads by hand to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if present

Secures the inner water tube assembly in your dishwasher. Replace if cracked, loose, or leaking. Rotates clockwise for removal. Verify fit with model.

This is the lower spray arm assembly that sits at the bottom of the dishwasher tub and rotates during the wash cycle to spray water onto dishes. It distributes pressurized water through small nozzle holes to clean the items on the lower rack. Replace this arm if dishes on the bottom rack are not getting clean, if the spray holes are clogged or damaged, or if the arm is cracked and no longer spins freely.

Fix a dishwasher motor that hums or won't start. This run capacitor provides the phase shift needed for smooth motor operation. DIY repair in 30-45 min.

This is a rubber gasket that seals around the door vent opening on a dishwasher, preventing steam and moisture from escaping into areas where they can cause damage. It fits between the vent assembly and the inner door panel. Replace this gasket if you notice moisture or steam leaking from around the vent area, water dripping down the front of the door, or if the gasket appears cracked, warped, or deteriorated.