Gy396lx802 Parts

Installed it according to video watched. Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

Replaced glass and missing screws. Hardest part was removing the old glass because of the double sided tape. Read more

I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more

The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more

The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more

Easy fix, this was an identical match to the fan that was in the oven. The only thing missing was the foam strip, that easily came off the old fan assembly and stuck to the new one. The hardest thing was finding the part, and with a picture to verify. I have found appliancepros.com has a large list of available parts,easy to find in their inventory of available items, and some of the best prices as well. This is a Whirlpool convection slide in oven, and the Whirlpool site was worthless, did... Read more

The plastic piece on the handle where the screw goes in to hold glass door up had broke. I ordered new handle, the retainer pieces that go over the plastic pieces to lock it all in and screws that were suggested. The screws were the wrong ones. They were way too small. I already had one screw and thankfully only had to buy 1 new one because the screw was $40 and shipping’s $10 for it AND it’s on back order right now. The old retainer ring that goes over plastic piece was a nightmare to remove... Read more

Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job. The fix only took about 15 minutes because I was prepared after watching the video. Read more

Ordered the right screw and screwed it in. Door now properly secured. Read more

• Door won't close

Found the parts on Appliance pros (love the website navigation); ordered on a Sunday afternoon and they were delivered on Tuesday afternoon. I had the drawer repaired within 15 minutes of Fed Ex delivering the package. No tools required other than my fingers! The original part was riveted to the drawer, these replacements are bolts with nuts and lock washers. Makes me wonder why this was not the original design. The riveted design NEVER seems to hold up to consumer use. Why do it on an... Read more

Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !! Read more

Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more

Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more