Hss25ifmd Parts

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

I found the part numbers in an exploded view of the refrigerator. They then showed that that part number had been replaced by a new one. I ordered them on line from Appliance Parts Pros. The parts arrived a few days later and, in this case, were an easy install. The refrigerator looks like new. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

I ordered the parts one day and they were here the next. And I didn't fix my wife did she said it was a simple fix. Read more

Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

I ordered the Cover Pan glass, glass front gasket and gasket lower shield. The diagrams on Appliciancepartspros.com were very helpful in ordering the correct parts. Once the parts arrived at the house, I put the gaskets on the glass and slide the glass into place. Read more

Replaced the parts myself. Parts were very easy to put in and matches the originals as expected. Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

1) By using google to find videos on why the door wouldn't close, I found out I needed new cams, those same videos also showed how to remove and replace the door. 2) Then by googling the fridge model number and the word 'cam', I was able to find the parts. 3) Taking the door off was simple, I needed a phillips head screwdriver to remove the hinge cover, however the screws in the hinge plate were so tight, I needed a side handle socket wrench to loosen them. 4) The door itself is not hard to... Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

I used the replacement parts that I bought from your company and in 10 minutes I replaced the hinge cam riser & Cam thimble and it worked great. Thanks so much. I will always buy my parts from your company!!!!!!! Chuck Whitlock Read more