Htw249ask6ws Parts

Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.

Washer won't spin or agitate? This motor assembly powers the wash and spin cycles. Common fix for non-spinning or overheating washers. Moderate DIY.

Water pooling around your washer or slow draining? This external drain hose directs water from the washer to your standpipe or utility sink during the drain cycle.

Leveling leg for top-load washers. Installs at the base to stabilize the unit and adjust height. Replace if cracked, broken, or missing to restore balance.

Fix a washer that won't agitate or spin with this drive motor. Powers drum rotation and agitation for effective washing. DIY-friendly replacement part.

Secures the lid lock mechanism on your washer. Mounts around the strike area where the lid lock engages. Replace if cracked, broken, or missing.

This pulley nut secures the washer's drive pulley to the shaft to keep the belt aligned and power transfer reliable. Replacing a worn or missing nut restores stable spin performance and helps prevent belt slippage and noise.

• Locks the drive pulley to the shaft for proper belt alignment and consistent power transfer
• A loose or stripped nut can cause pulley wobble, belt squeal, slippage, or the belt coming off
• Replace if the original nut is damaged, missing, or will not stay tight after adjustment

• Disconnect power and water supply; safely tip or elevate the washer for bottom access
• Remove the drive belt; hold the pulley while loosening the nut (verify thread direction—do not force)
• Hand-start the new nut to avoid cross-threading; tighten securely per service information and confirm pulley runs true
• Reinstall the belt, verify alignment, and rotate by hand before restoring power

Washer won't start or lid won't latch? This lid lock striker engages the lock assembly to secure the lid during wash cycles. Simple DIY fix.

Size: 10-32 GXTT FLP.595 S

Fix a broken or cracked cycle selector knob that won't turn or select wash settings. This control knob assembly restores reliable cycle selection in minutes.

Washer won't start or lid lock fails? This harness clip secures the lid lock wiring to prevent chafing and intermittent connection issues. Quick fix.

Original OEM Phillips wafer head screw 8 - 18 X 3/8 inch

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

Washer not filling with water or filling slowly? This 2-valve wire harness connects your control board to water valves, restoring proper fill and rinse cycles.

Fix leaks or loose connections in your washer with this clamp. Secures hoses, sensors, and wiring harnesses. Simple installation takes minutes.

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed