Htx21gaskww Parts

Fix a dryer that hums but won't start with this motor drive and pulley assembly. Powers the drum and maintains proper belt tension and alignment.

Fix a dryer that won't heat properly or overheats with this thermostat. Senses exhaust temperature to regulate heat cycles and prevent damage.

Lint trap duct slides provide smooth operation for your dryer's lint screen. Replace if slides are cracked, broken, or filter doesn't glide properly.

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

This valve and pipe assembly regulates and routes fuel through the dryer's system so the burner can ignite and maintain heat. Replacing a failing assembly restores reliable heating performance and consistent drying results. What it does

• Opens and closes to control fuel flow to the burner when heat is called for
• Directs fuel from the inlet to the burner orifice through a rigid manifold/pipe
• Helps maintain safe shutoff when the dryer is idle
• Common symptoms of a failing assembly: no heat, intermittent heat, or burner failing to ignite

• One valve-and-pipe assembly

• Disconnect power and shut off the gas supply before servicing
• Use only gas-rated fittings/sealant as specified by the manufacturer; do not overtighten connections
• After installation, check all joints for leaks with a soap-and-water solution
• Restore power and gas, then verify proper burner ignition and stable heating

The MOTOR & BLOWER ASSEMBLY is an OEM part for GE dryers. It contains both the drive motor that tumbles the dryer drum as well as the blower motor that circulates air through the heating system. This dual-component assembly works together to simultaneously tumble clothes while pushing heated air into the dryer cylinder.

Causes of a bad motor and blower assembly can include failures of either the drive motor or blower motor. Wiring issues or damaged components internal to the assembly housing can also impact performance.  

Symptoms of a bad motor & blower assembly include:

• The dryer drum not spinning or tumbling clothes
• Inadequate or no airflow through the dryer 
• Dryer not heating or cycles taking excessively long
• Loud buzzing or grinding noises from internal motors

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Dryer won't heat or overheats? This thermostat regulates temperature during drying cycles. Direct-fit part for common GE dryer models. DIY-friendly repair.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Dryer squealing or drum won't turn? This idler arm assembly keeps the drive belt tight and aligned for smooth drum rotation. Moderate DIY repair.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Dryer not heating or taking too long to dry? This gas valve assembly controls gas flow to the burner for reliable heat. Restores even drying performance.

Dryer not heating? This gas valve and burner assembly controls gas flow to ignite heat. Common fix for no heat or gas leak issues in gas dryers.

The Backsplash Assembly for Dryer is an OEM replacement part for GE electric and gas dryers. It forms the wall at the back of the dryer cabinet, protecting internal components from water, dust, and impact damage. This structural piece is important for dryer integrity. 

Causes of a bad backsplash assembly include normal wear and tear, accidental impacts, or rust forming behind the panel if moisture penetrates cracked seals. 

Symptoms of a bad backsplash assembly include:

• Visible cracks, warping, or denting of the panel material
• Looseness allowing gaps or movement of the assembly  
• Internal rust or component damage over many wash/dry cycles

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

Dryer won't start or cycles won't select? This rotary switch translates knob rotation into control signals. Fixes unresponsive or erratic cycle selection.