Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Color: Black The Bottom Trim Channel is an OEM part for GE ranges and wall ovens. This trim piece attaches along the bottom front edge of the oven cavity, creating a seamless facade. The bottom trim channel is responsible for covering any unsightly gaps and providing a sleek, finished look. It also acts as a protective barrier, shielding internal electronics and insulation from accidental impacts or liquid spills on the counter below. Symptoms of a bad bottom trim channel include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
The part was sent so fast we had it fixed right away. Very easy to repair. Read more
Restores bright interior lighting in your oven or range. Replace when bulb burns out to clearly see food and monitor cooking progress. Verify G9 base fit.
I searched and searched for a bulb with no luck. I peered into the darkness wondering if my food d was done? Would my pot run over? Then I found your site and met the goal of finding light again. I bought the bulb and shoved it in and all my needs we met. Read more
Replacement control knob for range cooktop. Mounts on infinite switch stem to adjust burner heat levels. Needed when original knob is cracked, broken, or missing.
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Broiler quit heating? This upper broil element restores intense top heat for fast, even browning and searing. Easy DIY replacement in about 20 minutes.
Ordered replacement, took out old element and put in the new one. Very easy, and it works! Read more
Control knob for electric range burners. Mounts on the control panel to adjust heat settings. Replace if cracked, broken, loose, or missing.
This is a genuine OEM replacement nut that is used on convection oven fans. This nut holds the fan onto the spindle. If the nut becomes lost during repairs to the fan, it will need to be replaced before the fan will work. This nut locks the fan to the spindle to turn and move the air around inside the oven. The fan helps the food to cook more evenly and reduces areas in the oven that are not cool enough or hot enough. If the fan is not working, the convection oven will not cook correctly.Convection ovens are different from regular ovens, and the fan is part of the reason. Convection ovens use the fan and an exhaust system to move the heat around inside the oven to cook food more evenly and faster. Many convection ovens have a setting that allows the oven to be used as a regular oven. If the nut is missing and the fan is inoperable, the oven can be used for regular cooking if it has this feature. Otherwise, the convection oven should not be used until the nut is replaced.This nut is a silver metal replacement part that is sold individually. It is designed for use in convection ovens made by GE and Kenmore.
I took the cover off and the fan had separated from the bushing. Ordered a new fan and nut and it took all of 5 minutes to replace. Probably saved $159.99 service call repair and that is with a coupon. Any one can do this repair, just make sure the oven is cold as you will come in contact with metal parts. Read more
This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more
This outer door panel replaces the decorative exterior panel on your microwave door. It restores a clean, factory appearance and provides proper support for the handle after dents, cracks, or finish damage.
Took off door, removed broken outer glass cover, and installed new part. Read more
White oven door handle that mounts to the front of your range door. Replace if cracked, broken, or damaged from over-tightening or daily wear and tear.
Remove and replace door handle. Make sure to keep screw spacers in place and do not over torque screws! Read more
Adjustable leveling leg for electric ranges. Installs on the bottom corner of the unit. Replace if broken, cracked, or missing to level your range.
Dismantled the upper part of the stove and removed old part. Had to super glue plastic parts of the underneath part where the touch pad is to be attached to. Put in new touch pad. Worked fantastic. Read more
White control knob for electric ranges and cooktops. Replaces broken, cracked, or missing knobs on burner controls. Direct-fit replacement part.
Just a simple install my maintenance man just put it in with no problems. Read more
Burner element burned out and quit working? This dual radiant surface element restores fast, even heating beneath glass cooktops. 10-15 minute repair.
I broke two of the elements in my GE Profile cooktop because I failed miserably at removing the glass top. It pays to do your research, kiddies. All it takes is a Number 10 Torx bit to remove 12 screws holding the glass to the body of the appliance, and it lifts straight up. I was replacing the glass because it broke during my home's construction. Anyway, you need a 1/4" nut driver to remove the mounting tabs on the bottom of the old element and transfer them to the new one. The whole swap out... Read more
The Radiant Element Spring is an OEM part for GE electric ranges. This spring supports the radiant element coil and provides the necessary tension to allow the coil to glow red-hot during the cooking process.
Causes of a bad spring can include fatigue from repeated heating and cooling cycles, damage due to impact or mishandling, or corrosion over extended use.
Symptoms of a bad radiant element spring include:
Includes 12 washers.
Indicator light lens covers and diffuses the panel light on your range or oven. Replace when cracked, discolored, or missing to restore visibility.
Super easy with your parts and directions Read more