Jdb8895aas Parts

This power cord strain relief secures the cord where it passes through the appliance cabinet, protecting the jacket and preventing pull on internal connections. Replacing a cracked or missing connector restores a safe, stable cord entry. What it does:

• Secures the power cord at the cabinet entry to relieve strain on internal terminals or junction connections
• Provides a protective bushing to reduce abrasion of the cord jacket against cabinet edges
• Helps maintain proper routing and support for the incoming power cord
• Typical signs it's needed: loose or wobbly cord at entry, broken/missing connector, or visible chafing on the cord jacket

• 1 strain relief connector

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove the access cover, release and remove the old strain relief, and route the cord through the new connector
• Seat the connector fully so it captures the cord's outer jacket—not the individual conductors
• After reassembly, verify the cord is secure and does not move at the entry point

This de-coupled drain housing creates a sealed, vibration-isolated connection in the appliance's drain path. Replacing a cracked or leaking housing restores reliable draining performance and helps prevent water leaks and rattling during the drain cycle.

• Forms the rigid, sealed connection between the drain path and mating components
• Isolates pump vibration from the chassis to reduce noise during drain
• Directs wastewater efficiently out of the unit during the drain cycle
• Common symptoms of a failed housing include standing water, leaks under the unit, loud vibration/buzzing while draining, or visible cracks/broken tabs

• Disconnect power and water supply before servicing; allow any hot water to cool
• Access the drain area and place a towel or pan to catch residual water
• Move clamps/hoses, then transfer any reusable seals or grommets; replace worn seals as needed
• Secure all connections and clamps; run a short test and check carefully for leaks

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This dishwasher circulation pump and motor assembly moves wash water through the spray arms during the cycles. Replacing a failed or noisy unit restores proper water flow, spray pressure, and reliable cleaning performance.

• Circulates water from the sump through the spray arms during wash and rinse
• Provides the pressure and flow needed for effective cleaning
• Common failure symptoms: little or no spray action, poor cleaning results, loud humming/rumbling/grinding during wash
• Water leaking from the pump area can also indicate a problem with this assembly

• Disconnect power at the breaker and shut off the water supply before servicing
• Access from the bottom/front; remove the toe panel and pull the dishwasher out if needed for clearance
• Expect residual water; place towels or a tray to catch spill, and note wire/connector orientation before removal
• Ensure all connections and seals are properly seated; run a short fill/rinse to check for leaks before reassembly

This replacement screw secures appliance components in place. Swapping a stripped, rusty, or missing fastener restores a tight fit for panels, brackets, and handles, helping reduce vibration, rattling, and premature wear.

• Secures panels, brackets, trim, or hardware to the appliance frame
• Replaces missing, stripped, or corroded fasteners that no longer hold
• Helps eliminate looseness, rattling, or misalignment
• Restores proper fit and finish after service

• Disconnect power; shut off water supply if servicing a dishwasher.
• Match thread and length to the original screw before installing.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• When applicable, replace paired screws together for even clamping.

Keep utensils organized and secure during the wash. This silverware basket sits in the lower rack and holds flatware and small items so water can circulate freely for effective cleaning and to help prevent obstructions.

• Organizes forks, spoons, knives, and small items in the lower rack to keep them from moving during cycles
• Promotes proper spray coverage by allowing water to flow through the basket's grid
• Helps prevent loose utensils from blocking the spray arm or damaging internal components
• Replaces a cracked, warped, or missing basket; common signs include broken sections or utensils falling through

• Disconnect power at the breaker before servicing
• Remove the old basket and place the new basket in the lower rack; no tools required
• Ensure the basket sits flat and does not contact the spray arm
• Follow your owner's manual for safe utensil loading practices

This tub mount assembly secures the tub to the cabinet/frame, keeping it properly positioned so the appliance operates smoothly and quietly.

• Supports and stabilizes the tub during operation
• Helps reduce vibration, noise, and movement
• Replace if you notice excessive tub movement, rattling, or mounting damage
• Restores correct alignment after a broken or worn mount

• Disconnect power and water before servicing
• Access mounting area; support the tub to relieve stress on fasteners
• Transfer any reusable hardware and align the new mount precisely
• Tighten fasteners evenly; verify clearance and operation before restoring power

Dishwasher rack rear bowl tine. For the front tine order 12002218. For the tine clip order WPY912709.

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

Drain hose (loop) that routes washer wastewater and forms a high drain loop to help reduce backflow and siphoning. Replaces cracked, kinked, or deteriorated drain hoses to restore proper draining and reduce leaks. What it does:

• Directs wastewater from the appliance to the household drain to maintain proper drainage.
• Forms a high drain loop to help prevent backflow and siphoning into the washer.
• Replaces worn or damaged hoses that can cause leaks, slow draining, or standing water.
• Works with the appliance's factory drain connection and clamps.

• Disconnect power and turn off the water supply before servicing.
• Route hose to create a high loop above the cabinet connection and secure with clamps to prevent kinks or sagging.
• Use appropriate clamps or fasteners and tighten connections; inspect for leaks after restoring power and water.

Color: White. Screw for lower toe panel. For black screw use WP302868, for biscuit use 3400865.

Used on the ends of the tines inside the dishwasher rack.