Jgd8345 Parts

Sealed burner assembly that supplies a protected gas flame for a gas range, restoring consistent heat and helping keep spills and debris out of the burner box. Designed as a direct-replacement assembly for affected burners. What it does

• Provides the sealed gas flame source used for cooking on a gas cooktop
• Restores even heat distribution when a burner is warped, damaged, or not producing a steady flame
• Helps prevent spills and food debris from entering the burner cavity, reducing corrosion and ignition problems
• Symptom linkage: commonly replaced for uneven heating, weak or irregular flame, visible burner damage, or excessive soot

• Includes 1 sealed burner assembly

• Turn off the gas supply and electricity to the appliance before starting any service
• Follow model-specific disassembly steps (lift or remove cooktop/grates as required); do not force fittings or gas connections
• If you smell gas, shut off the gas supply immediately

• WP3403M075-29 — confirm this matches your original part before ordering

Burner won't light or flame sputters? This gas valve controls flow to restore reliable ignition. Moderate DIY repair—requires manifold access.

Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

Fixes burner knob that won't turn, push down, or ignite. This gas valve controls flame height and regulates gas flow to one surface burner on your cooktop.

This single valve switch is the electrical control that activates a single solenoid valve, restoring proper valve operation so the appliance can open or close the water/flow circuit as designed. It replaces a failed or non-responsive valve control switch. What it does

• Sends the electrical signal to a single solenoid valve so the valve opens or closes when commanded.
• Commonly used when a valve fails to energize, causing no water flow or intermittent operation.
• Helps resolve symptoms such as the valve not activating, intermittent dispensing, or an appliance that won't fill.
• Works as the user-commanded switch interface between control electronics and the valve assembly.

• One (1) single valve switch

• Disconnect power to the appliance before starting any repair to avoid shock.
• Turn off the water supply if the repair requires disconnecting water lines.
• Verify connector orientation and secure electrical connections; do not force connectors.

If your gas burner won't ignite or flame height is inconsistent, the burner valve likely needs replacement. Moderate DIY repair requiring panel removal.

Fix a burner that won't stay lit or has a weak yellow flame. This venturi tube mixes air with gas for proper combustion. Easy 15-minute repair.

Mounting screw secures panels, brackets, and components inside your oven. Replace missing, stripped, or damaged screws to restore proper fit.

This double valve switch assembly controls two valve circuits to manage water flow and valve operation in compatible appliances. It replaces a failed switch to restore proper valve control and appliance function. What it does:

• Acts as the electrical switching assembly for two valve solenoids or circuits
• Allows the appliance control board to open and close water valves as needed
• Commonly linked to symptoms like no fill, continuous fill, or intermittent valve operation
• Helps stop erratic or unresponsive valve behavior when the original switch fails

• One double valve switch assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Verify power is off with a meter and document wire locations or take photos before disconnecting
• Handle connectors carefully; ensure proper seating and secure mounting during reassembly

Weak or uneven burner flame? This venturi tube channels the gas-air mixture from valve to burner for proper ignition. Straightforward replacement.

This relay change kit replaces the failed relay assembly that controls motor or compressor power, restoring proper electrical switching for normal operation. Use this kit to replace a worn or intermittently working relay with an exact-fit factory component. What it does

• Switches power to the motor/compressor when the appliance calls for it
• Restores reliable start and run signals when a relay has failed or sticks
• Addresses symptoms like clicking on start, no motor/compressor operation, or intermittent runs
• Helps prevent damage from repeated failed start attempts

• One relay change kit

• Disconnect power before servicing to avoid shock or damage
• Replace only with the exact OEM relay kit for safe, reliable operation
• Verify wiring and connectors are secure and undamaged before restoring power

Replacement control knob for cooktop control shaft. Install a new knob if your original is cracked, stripped, broken, or missing to restore secure grip.

Grease drain jar collects drippings beneath your grill cooking surface. Replace if cracked, broken, or missing to prevent messy grease buildup.

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

Replace your cooktop's gas manifold if it's cracked, damaged, or leaking. This pipe component distributes gas from the supply line to the burners.