Jnm1541dnbb Parts

This latch body is the door latch component that secures the appliance door during operation, restoring reliable closure so cycles can run normally. Use it to replace a worn or damaged latch that won't hold the door closed. What it does:

• Engages the door striker to hold the door closed and maintain a proper seal during operation
• Works with the door latch mechanism so the appliance can complete cycles that require a closed door
• Common symptom: door won't stay closed, is difficult to latch, or feels loose at the latch point
• Replacing a damaged latch body can prevent intermittent door-open errors and restore normal door operation

• Disconnect power (unplug or turn off circuit breaker) before starting any repair
• Remove the door or access panel as needed; keep track of fasteners and any trim pieces
• Handle door glass and trim carefully to avoid damage; test latch engagement before full reassembly

Made by GE. This microwave stirrer motor comes with a square shaped shaft and is usually located in the upper part of the microwave. For a D shaped shaft turntable motor order WB26X10038.

This control panel assembly is the front user interface housing for your appliance. Replace a cracked, loose, or damaged panel to restore a secure fit and dependable access to the controls for everyday operation.

• Holds and aligns the keypad, display, and related switches for proper use
• Provides mounting points for the electronic control components
• Protects internal controls from everyday wear and minor impacts
• Helps address issues like a broken bezel, missing tabs, or a loose/misaligned panel
• Restores a clean, factory look to the user interface area

• Disconnect power at the breaker before servicing
• Remove trim/grille and mounting screws; support the panel to avoid stressing wiring
• Transfer any brackets, switches, and display/board from the original panel, noting wire locations
• Reassemble and test all controls before final mounting

This glass light cover shields and diffuses the cooktop light, protecting the bulb from heat, grease, and splatter while maintaining clear, even illumination over your cooking surface.

• Covers and protects the cooktop light bulb
• Diffuses light for more even illumination and reduced glare
• Helps keep grease and debris out of the light cavity
• Replace if cracked, missing, discolored, or not staying secured

• Disconnect power to the appliance before servicing and allow the area to cool
• Support the cover while removing any retaining screw(s) or release tabs
• Reuse original hardware/clips as applicable and seat the cover fully
• Restore power and test the light for proper operation

This holder nut assembly secures a component to the appliance frame, restoring proper mounting and reducing vibration or movement. Replace a damaged or missing holder nut to keep connected parts stable and functioning. What it does:

• Secures a component or assembly to the appliance frame or mounting bracket
• Prevents looseness, rattling, and misalignment caused by worn or missing mounting hardware
• Restores a safe, stable connection that helps maintain normal operation
• Matches OEM mounting geometry for a direct replacement when the original nut is damaged

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the mounting area by removing the appropriate panel or cover per your model's service instructions
• Start threads by hand to avoid cross-threading, then tighten with the correct tool; do not overtighten
• If any fasteners or nearby components are damaged, replace them as needed for a secure installation

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

Magnetron assembly that produces the microwave energy used to heat food. Replacing a failed magnetron restores heating performance so the oven can warm and cook food properly. What it does

• Generates the microwave energy that heats food; a failed magnetron typically causes little or no heating.
• Can produce loud humming or buzzing if failing.
• May cause sparking/arcing inside the cavity or a burning/odd smell when faulty.
• A bad magnetron can lead to blown fuses or tripped safety devices.

• High-voltage component — unplug the appliance before service. The high-voltage capacitor can retain dangerous charge; do not touch terminals.
• Recommended for installation by someone experienced with microwave high-voltage systems.
• Ensure all panels and covers are reinstalled before powering on.

This evaporator fan motor assembly circulates cold air through the refrigerator compartment to help maintain even cooling and proper temperature control. Replacing a failed fan restores airflow and helps the appliance cool correctly. What it does:

• Moves air across the evaporator coil so the refrigerator/freezer can cool efficiently
• Commonly replaced when there is little or no airflow from the fresh-food or freezer section
• Can stop excessive frost build-up on the evaporator caused by poor circulation
• May reduce unusual noise if the original motor bearings have failed
• Helps prevent uneven temperatures that can cause food spoilage

• One evaporator fan motor assembly as shown

• Disconnect power to the appliance before starting any repair
• Access may require removing interior panels or the evaporator cover
• Handle the fan blades carefully to avoid bending or cracking; ensure proper blade seating on the motor shaft

This oven grille trims the front of the range or built-in oven, restoring a finished appearance and helping direct airflow. Replaces a damaged or missing front trim to improve fit and finish. What it does:

• Covers and protects the gap between the oven cavity and control/face trim
• Directs vented airflow away from the control area for proper airflow routing
• Restores the oven's factory appearance when original grille is cracked, warped, or discolored
• Helps prevent small debris from entering the vent opening

• One grille trim piece

• Designed for direct replacement; verify fit to your specific model before installation
• Remove power to the appliance before beginning any removal or installation
• Use appropriate hand tools and avoid over-tightening fasteners to prevent cracking

This noise filter assembly is a direct-replacement line filter that helps reduce electrical interference and appliance noise for compatible GE appliances. It restores cleaner power to control boards and can help stop buzzing or interference-related behavior. What it does:

• Suppresses incoming electrical noise and RF interference on the power line
• Helps prevent control glitches and erratic behavior caused by voltage transients
• Can reduce humming, buzzing, or audio/EMI interference from the appliance
• Supports stable operation of electronic controls and sensors

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle wiring and connectors carefully; match wires/terminals exactly on reassembly
• Secure the filter in its mounting location and ensure wiring is routed clear of moving parts

This cover-damper is the replacement plastic cover that fits over the refrigerator air damper to help direct cold air between compartments for more consistent cooling. Replaces a cracked, broken or missing damper cover. What it does:

• Protects the damper assembly and helps channel airflow from the evaporator to the fresh-food and freezer compartments
• Restores proper air direction when a broken cover causes uneven temperatures or poor cooling
• Works with the damper to reduce drafts and improve compartment temperature balance
• Simple, passive part that mounts to the damper housing

• One cover-damper

• Disconnect power to the appliance before starting any repair
• Remove interior panels or shelves as needed to access the damper housing; handle plastic clips gently to avoid breakage
• Verify fit and orientation against the existing part before finalizing installation
• If the damper motor or actuator is damaged or the issue persists after installing this cover, inspect the full damper assembly

This motor ventilation part is the replacement vent fan motor that moves air through the appliance for proper cooling and exhaust. Replacing a failed vent motor restores airflow and helps the appliance maintain safe operating temperatures. What it does

• Spins the ventilation fan to move air for cooling or exhaust
• Helps prevent overheating by promoting proper airflow
• Can stop symptoms such as reduced or no exhaust, weak airflow, or abnormal motor noise
• Works as the airflow drive component in the appliance's ventilation system

• Disconnect power to the appliance before starting any repair
• Basic mechanical skill and common tools are usually required; refer to the service manual for disassembly instructions

This washered screw secures panels and internal components where a combined screw-and-washer fastener is required, restoring proper fit and stopping movement or rattling. Simple replacement with the correct fastener keeps assemblies aligned and stable. What it does

• Secures panels, brackets or components where a washered screw is specified
• Replaces missing, stripped or corroded fasteners that allow vibration or gaps
• Helps stop rattling, loose panels or misaligned parts caused by a failed screw
• Provides a sealed bearing surface to distribute load and prevent pull-through

• One washered screw

• Disconnect power and/or water to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid cam-out and fastener damage
• Align parts before tightening and snug; avoid over-tightening which can strip threads or crack plastic