Jtb86b0f3bb Parts

Mounting screw secures panels, brackets, and trim on refrigerators and washers. Replace when fasteners are missing, loose, stripped, or damaged.

Fix a refrigerator that runs constantly or won't maintain proper temperature. This cold control thermostat regulates cooling cycles. DIY repair.

Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.

Color: white. Measures about 2/3 of an inch wide by 1/2 an inch deep.

Fix ice buildup on evaporator coils with this refrigerator defrost heater. Restores proper airflow and cooling. Simple 20-minute installation.

Fix frost buildup and poor cooling caused by a failed defrost heater. This evaporator heater melts ice during defrost cycles. Moderate DIY repair.

If your ice cube tray is broken or missing, this replacement tray forms and holds standard-sized ice cubes in your freezer. Simple installation.

Fix a refrigerator that's not cooling properly with a new condenser fan blade. Restores airflow across condenser coils for consistent temperatures.

White refrigerator door gasket seals the door edge to prevent cold air leaks and improve energy efficiency. Replace if torn, cracked, or loose. Verify fit with your model number before ordering.

Seals the fresh-food door to maintain cooling and prevent warm air entry. Replace when cracked, torn, or compressed. Verify fit with your model number.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

This is a replacement pin wheel that secures and guides a mating linkage or small shaft in the appliance, restoring proper alignment and smooth movement. A direct-fit replacement when the original wheel is cracked, worn, or missing. What it does

• Holds and stabilizes a small rotating shaft or linkage to maintain proper component alignment
• Allows smooth transfer of motion between mating parts to prevent skipping or binding
• Worn or broken pin wheel can cause noise, intermittent movement, or improper function of the associated mechanism
• Small, inexpensive part that prevents further wear to adjoining components when replaced promptly

• One pin wheel

• Disconnect power to the appliance before starting any repair
• Access and removal often require removing a panel or nearby components; keep fasteners organized
• Inspect the mating shaft/clip and replace any damaged hardware for reliable operation
• Tighten and test moving parts by hand before restoring power; follow OEM service manual steps

This terminal cover protects the appliance's power connection area, keeping wiring and terminals enclosed to reduce shock and short risks. It's a direct-replacement trim piece that restores the factory protective barrier around the terminal block. What it does:

• Covers and shields the terminal block where the power cord connects, helping prevent accidental contact.
• Helps reduce the risk of shorting or arcing at exposed power connections.
• Addresses symptoms like visible exposed terminals, loose or unprotected wiring at the power entry area, or a missing/broken cover.
• Restores the appliance's intended safety enclosure after repair or shipping damage.

• One terminal cover

• Always disconnect all power (unplug or shut off breaker) before accessing the terminal block.
• Remove the old cover and position the replacement over the terminal area so mounting holes align; secure with the original screw(s).
• Inspect terminal screws and wiring for tightness and damage while cover is off; do not attempt electrical repairs.
• If terminals or wiring are damaged, replace or repair those components before reinstalling the cover.

Cracked or broken ice cube tray? This plastic tray restores manual ice-making in your refrigerator. Simple drop-in replacement, no tools required.

This is a small roller wheel designed to support and allow smooth movement of components inside a refrigerator cabinet. It typically mounts on a bracket to help drawers, shelves, or other sliding parts glide easily. Replace this roller if a drawer or shelf is difficult to slide, makes scraping noises, or the wheel is cracked, flat-spotted, or no longer turns freely.

Replacement mounting screw for securing freezer panels, brackets, and components. Restores proper fastening where original screw is missing, stripped, or damaged.