Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement oven rack that slides into side supports to hold cookware at the desired baking level. Replace if bent, worn, or missing to restore level support.
Put the new one in the oven. Read more
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.
We replaced the broken door hinge. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Oven overheating or won't heat properly? This thermal limit switch monitors temperature and cuts power to prevent damage. Resets automatically when cooled.
Oven not heating or preheating slowly? This lower bake element provides bottom heat for even cooking. Straightforward DIY repair for most models.
Button board housing secures control buttons and PCB in your oven's control panel. Replace if cracked, broken, or worn to restore stable button alignment.
I ordered the three parts listed and now my oven is beautiful, functional and like new again. I first had to figure out that the original parts are no longer available and had to perform an oven upgrade. Obviously the original design was flawed and the new design works perfectly and looks great! The whole repair cost was about $328 with shipping included. The parts were here in just a few days, about 2 to 4 days (some in two days, one in 4 days). Much cheaper and easier than replacing the... Read more
Oven won't start self-clean cycle or door won't lock? This door latch assembly secures the door and signals lock status. Moderate DIY repair.
Very easy fix. 3 screws on the front panel and two screws on the new switch. Read more
Fix an oven door that won't close or lock properly with this latch and tape assembly. Restores secure door engagement for safe cooking and self-clean cycles.
Replacement screw for securing oven components, panels, and brackets. Restores tight mounting when original screws are missing, stripped, or lost.
Replace screws Read more
Thermal insulation that fits between inner and outer oven door panels along the side edge. Replace when burnt, brittle, cracked, or missing from wear.
Replaced the insulation and followed oven door removal video on YouTube. Read more
Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.
Decorative nameplate badge for oven and range front panels. Replaces missing, worn, or damaged emblems to restore factory appearance. Includes adhesive.
I retrofitted the unit to the 9.5" since the 17.5" is discontinued due to faulty design. I used parts AP4484272, AP4484324, AP4484499, 6 of AP4380294, AP3993470. It was simple. It looks incredible! Works Perfect! -Tommy Lentsch www.TommyLentsch.com Read more
This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.
I did some research on my own and then spoke with the “Pros” at Appliance Parts Pros. Both confirmed the main board needed to be changed. The other less likely item was the oven sensor. I changed the sensor first as it was inexpensive. The error codes continued. Subsequently, I then changed the main board which was slightly difficult. When changing 2 screws hold the board in place on each front corner only. Also suggest you take a picture of wiring. I replaced wiring in place from old board to... Read more
6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.
Replaced all of the control parts for the GE oven. Read more
Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.
Installed the part I ordered Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.