Kdfe1044dss Parts

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This factory fastener replaces a worn, stripped, or missing screw to securely hold appliance components in place, restoring proper fit and reducing vibration, noise, and loosening issues. It helps maintain alignment and safe operation of the affected assembly. What it does:

• Secures panels, brackets, or internal components as designed for the appliance
• Maintains assembly alignment for reliable performance
• Helps prevent rattling or vibration from loose hardware
• Replace when the original screw is missing, corroded, stripped, or damaged

• 1 screw

• Disconnect power; for gas- or water-connected appliances, shut off supply before servicing
• Match the screw to its original location and retain any spacers or clips used with the original
• Start threads by hand to avoid cross-threading; use the correct driver size
• Tighten until snug; do not overtighten to avoid stripping threads

The Top Spray Arm is an OEM part for Whirlpool dishwashers. It serves an important role on the upper rack, directing a spray of water across dishes during the wash cycle to thoroughly clean all surfaces. As a rotating component, the top spray arm endures constant motion which can cause wear over time.

Causes of a bad top spray arm include deterioration or cracks in the plastic from extended use, or blockages that restrict water flow.

Symptoms of a bad top spray arm include:

• Incomplete cleaning of upper rack dishes
• Buildup of food debris or grime that won't rinse away
• Noticeably weaker spray pattern from the arm nozzles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part is the rinse-aid cap/knob that seals the dishwasher's rinse-aid reservoir in the door-mounted dispenser. A secure cap prevents leaks and evaporation so rinse aid dispenses properly, helping reduce spots and improve drying.

• Seals the rinse-aid fill port on the dispenser to prevent leaks and evaporation
• Helps the dispenser meter rinse aid during the final rinse
• Common symptoms of a bad/missing cap: loose or cracked cap, rinse-aid odor or residue inside the door, rinse aid depleting quickly, increased spotting on dishes
• Restores proper sealing and helps maintain consistent drying performance

• Disconnect power at the breaker and turn off water before servicing
• Open the door, remove the old cap by turning counterclockwise
• Clean the sealing surface; install the new cap by hand and tighten until snug—do not overtighten
• Run a quick cycle and check for leaks around the dispenser

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This cup shelf clip secures the dishwasher's fold-down cup shelf to the upper rack. Replacing a cracked or missing clip restores a stable shelf so cups and small items stay organized throughout the wash cycle.

• Fastens the cup shelf to the upper rack wire to prevent wobble or detachment
• Helps the shelf pivot and lock properly when raised or lowered
• Typical symptoms: shelf hangs loose, falls off, won't stay in position, or the original clip is broken/missing

• Open the door and fully extend the upper rack; remove the rack if needed for access
• Squeeze the old clip's tabs to release and lift it off the rack wire or shelf
• Align the new clip on the rack wire and press until it snaps securely into place
• Verify the shelf moves and locks correctly before running a cycle

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This replacement screw secures appliance panels, brackets, and internal components. Install it when original hardware is missing, stripped, or corroded to restore a solid, factory hold and help stop vibration, rattles, and misalignment.

• Provides secure attachment for covers, brackets, and assemblies
• Replaces missing, damaged, or rusted hardware
• Helps resolve loose panels, buzzing/rattling noises, or shifting parts
• Supports proper alignment and reliable operation when tightened correctly

• Disconnect power; shut off gas/water if applicable before service
• Match thread and length to the original; replace in the same location
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If washers, spacers, or threadlocker were present originally, transfer or replace them

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool dishwashers. It secures the sliding dishwasher rack at the rear of the tub.

Symptoms of a faulty stop clip include:

• Dishes shifting position or toppling during cycles of motion  
• Noisy clattering heard from partially-restricted rack movement
• The dishrack failing to fully retract or extend 

Over time, repeated force from dish impacts can bend the thin metal clip out of place. Fatigue causes it to lose retaining strength.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

The Panel Toe is an OEM part compatible with GE dishwashers. It is a discreet metallic strip located along the bottom front panel of the appliance. The toe provides protection and reinforcement to this high-impact area.   

Causes of a bad panel toe include normal wear from opening and closing the dishwasher door hundreds of times each year. Misalignment from door impact can also cause premature deterioration.

Symptoms of a bad panel toe include: 

• Visible cracking, bending, or detachment of the toe strip
• Potential for other panel issues if toe integrity is compromised
• Possible denting or distortion of neighboring surfaces
• Aesthetic issues and reduced protection of front panel edges

This genuine GE replacement part restores the structure and helps prevent further damage. Compatible Dishwasher models also include some Hotpoint, Profile, and Kenmore units.
 

The Retainer is an OEM part for Whirlpool dishwashers. It securely holds the top spray arm in place underneath the dishwasher interior roof panel.

Causes of a bad retainer include cracking, breaking or deforming from repeated use and natural wear over time.

Symptoms of a bad top spray arm retainer are:

• Loosening or detachment of the upper spray arm during washing cycles
• Reduced or uneven water coverage for upper rack dishes
• Potential rattling or noise from an unsecured spray arm

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.