Kdtm404kps Parts

This Pad-ins is a factory-style insulation pad that helps reduce heat transfer and dampen vibration inside the appliance. It restores original fit and helps protect nearby components from heat and abrasion. What it does:

• Provides thermal insulation to limit heat transfer to adjacent parts
• Cushions and dampens vibration and noise from moving components
• Helps prevent chafing or wear where panels or parts contact each other
• Can reduce symptoms such as hot spots, rattling, or scuffing near the pad location

• Disconnect power (and gas, if applicable) before starting any repair
• Remove panels as needed to access the pad; take photos for reassembly
• Peel-and-stick or adhesive-backed pads should be positioned carefully; press firmly to ensure adhesion
• If replacing adhesive-backed pads, remove old adhesive residue and follow OEM placement for best fit

The Lower Door Seal Assembly is an OEM part for Whirlpool dishwashers. As a key component, this seal is designed to create a tight barrier between the door interior and tub during wash cycles. The pliable rubber seal provides a sturdy gasket to block water, detergent, and sound.

Causes of failure involve mineral buildup, cracks from repeated use, or degradation of adhesive over time compromising the seal. 

Symptoms of a faulty seal assembly include: 

• Puddles or leaks from beneath the door frame
• Higher water consumption or longer cycles   
• Increased noise levels during operation

This OEM Whirlpool replacement is also compatible with select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and other brands.

The Pump Filter is an OEM part for Whirlpool dishwashers. It is a filter that screens debris from entering the pump and wash arms during the dishwashing cycle.

The pump filter is responsible for catching food particles and other residue, preventing clogs and maintaining optimal water flow throughout the dishwasher. It ensures the pump and other internal components are kept clean.

Symptoms of a clogged or damaged pump filter include:

• Excessive noise or vibrations coming from the pump area
• Slow or reduced water drainage
• Built up residue in the filter housing or sump area
• Incomplete cleaning or drying results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Circulation Pump is an OEM part for Whirlpool dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles, ensuring that all dishes are cleaned thoroughly. The pump maintains a steady flow of water, distributing it evenly across the dishwasher's interior for optimal cleaning performance.

Over time, the circulation pump can fail due to factors such as wear and tear, blockage from debris, or electrical issues. A malfunctioning pump can compromise the dishwasher's ability to clean effectively, leading to unsatisfactory results.

Symptoms of a bad circulation pump include:

• Dishes not being cleaned properly
• Unusual noises coming from the dishwasher during operation
• Water not circulating or spraying inside the dishwasher
• Error codes related to water circulation issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Replacement door hinge designed to restore proper alignment and smooth opening for compatible refrigerator doors. Replaces worn or damaged hinges to reduce sagging, rubbing, and uneven closing for better seal and operation. What it does:

• Supports and pivots the refrigerator door for smooth opening and closing.
• Restores correct door alignment to improve gasket contact and cold-air seal.
• Stops door sag, uneven gaps, or rubbing against the cabinet.
• Helps eliminate noisy or stiff door movement caused by a worn hinge.

• Disconnect power to the appliance and remove food from the door area before starting.
• Support the door securely while removing and installing the hinge to prevent dropping or damage.
• Reuse original fasteners only if undamaged; replace any stripped or corroded hardware.

The Seal is an OEM part for Whirlpool dishwashers. It prevents water leaks from the dishwasher door during wash cycles and water heating drainage. Properly installed seals around the door perimeter maintain water pressure inside the dishwasher tub and ensure leak-free operation. 

Causes of a bad seal can include cracks or breaks after extended use of the door opening and closing, exposure to heat and chemicals from regular dishwasher operation, or loose or improper installation.

Symptoms of a bad seal include:

• Water leaks visible around the edge of the door during wash cycles
• Puddles or drips left on the kitchen counter or floor after use   
• Difficulty closing or latching the dishwasher door securely

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dishwasher detergent and rinse aid dispenser stores detergent and releases it at the correct point in the cycle while metering rinse aid. Replacing a worn dispenser restores consistent soap release, cleaning performance, and spot-reducing rinse aid delivery.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup at the programmed time during the wash
• Meters rinse aid into the final rinse to help reduce spotting
• Typical symptoms: detergent left in cup, dispenser door won't open, rinse aid not dispensing, or leaks around the dispenser area

• Disconnect power to the dishwasher before servicing
• Access from the inner door by removing the perimeter screws to separate the door panels
• Disconnect the wire harness, release the locking tabs, seat the new dispenser evenly, and tighten screws evenly to compress the seal
• Run a short cycle to check for leaks

The Dishwasher Plate-Latch Strike is an OEM part for Whirlpool dishwashers. It is a part that holds the dishwasher door shut during wash cycles. Precise alignment of the strike allows for tight sealing and proper engagement with the door latch.

Causes may arise from normal wear over lengthy use, deformations from repetitive door actions, or incidental damage.

Symptoms of a bad strike can include:

• Door that feels loose and doesn't fully latch closed
• Gaps seen around the door sealing surface
• Water leaks or insufficient drying performance
• Difficulty fully closing or reopening the door

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lower Spray Arm is an OEM component specifically designed for Whirlpool brand dishwashers. This lower spray arm attaches to the bottom rack and rotates during the wash cycle to distribute water and cleaning chemicals across dishes. 

Causes of a bad lower spray arm can include mineral buildup inhibiting movement, cracks or breaks in the arm itself, or broken or missing spray nozzles. 

Symptoms of a bad lower spray arm include:

• Inadequate cleaning or rinsing of dishes on the bottom rack  
• Noticeable buildup or residue left on dishes after washing
• Noises, squeaks, or grinding sounds coming from the lower spray arm area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

The Dishwasher Electronic Control Board is an OEM replacement part for  Whirlpool dishwashers. It serves as the central control unit, responsible for managing and regulating various functions and operations of the dishwasher.

Causes of a faulty Dishwasher Electronic Control Board include electrical malfunctions, power surges, or physical damage from impact or moisture exposure. 

Symptoms of a bad Electronic Control Board include:

• Dishwasher not starting or powering on
• Incorrect cycle selection or cycles not functioning properly
• Error codes or warning lights indicating control board issues
• Erratic behavior, such as irregular water fill or heating issues
• Failure to respond to user inputs or control panel buttons

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models, ensuring a perfect fit and reliable performance for your specific appliance.

The Drain Hose is an OEM part for Whirlpool dishwashers. It channels water out of the dishwasher tub and into the garbage disposal or drain after each cycle. This drain hose is specifically designed to withstand frequent temperature fluctuations and mineral deposits without compromising its integrity over time.

Causes of a bad Drain Hose can include mineral buildup inside the hose restricting flow, cracks developing from repeated flexing during drain cycles, or cuts or abrasions from rough handling or sharp surfaces.

Symptoms of a bad Drain Hose include:

• Water not draining properly or draining slowly after cycles
• Puddles or leaks found near or under the dishwasher
• Musty smells from standing water inside or around the unit
• Possible flooded floors near the dishwasher area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This heater terminal nut fastens the heating element stud on the outside of the tub, keeping the element seated and stable during wash and dry cycles. Replace if the original nut is missing, stripped, or corroded.

• Secures the heating element terminals to the tub exterior
• Maintains proper element position for consistent, reliable operation
• Direct replacement for a worn, missing, or rusted element terminal nut
• Common signs: loose heating element at the tub wall, rattling from the lower area, or visible damage/corrosion on the nut

• Safety first: Disconnect power at the breaker and allow the element to cool before servicing.
• Access the heater terminals from beneath the unit by removing the toe panel or carefully sliding the dishwasher out.
• Support the terminal stud and wiring while loosening/tightening to avoid twisting or stressing the element.
• Tighten snugly without overtightening; run a brief test cycle to confirm proper operation.

The Lower Dishrack Roller Assembly is an OEM part for Whirlpool dishwashers. As an integral component, the lower dishrack roller assembly supports smooth movement and positioning of the lower dishrack. Its precision ball bearings allow for effortless extension and retraction of the lower rack.

Causes of a bad lower dishrack roller assembly can include wear and tear of bearings over time, stripped or damaged rails, or failure of rollers due to excessive loading.  

Symptoms of a bad lower dishrack roller assembly include:

• Difficulty extending or retracting the lower dishrack  
• Noisy or stuck operation of the lower rack
• Rack failing to remain securely in place during wash cycles
• Dishes shifting or falling during wash due to uneven support

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, Kenmore, and some Maytag and GE dishwashers. 

The Hose is an OEM part for Whirlpool dishwashers. It connects the dishwasher pump and sump, functioning to drain and recirculate water throughout cycles.

Causes of failure can include mineral buildup inside the hose, splitting, and cracking of the lining from continuous heat and pressure usage over time.

Symptoms of a bad pump to sump hose include:

• Inadequate drainage and water removal from cycles
• Standing water left in the bottom of the dishwasher tub
• Leaks developing from hose connections at the pump or sump area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.