Kess907ss04 Parts

I simply replaced the knobs. Just frustrating because this small part surrounding metal rod to attach knobs is obviously defective and should be improved by Kitchen Aid. Read more

Replaced the panel with a new one, and put the new indicator lights on. Read more

Called up AppliancePartsPros and ordered the part. My husband took the oven door apart and had it replaced within 15 minutes. Read more

I recently shattered the outer glass on my Whirlpool oven door. (Side note for lesson learned...don't swat at a fly with a broom when its on the oven door. I didnt swing hard just a love tap but thats all it took ha ha) The toughest part of the fix was removing the broken glass as it had shattered into hundreds...no thousands of pieces. Thankfully it was taped on the inside and that held some of it together. I placed the door in our garbage can and put on a pair of gloves with a scraper to... Read more

I am a 78year old woman and 40 years ago I replaced the belt on a dryer but could not even consider such a feat today. I ordered the parts from you on line and also found the video that you very nicely have attached to the site and I saved this under my favorites. The baffles arrived within 3 days and due to my age was unaware that dryers now come in two sizes and the ones I ordered were for the smaller but same model. I worked with a very nice customer service agent on line who got me the... Read more

Replaced it with the part I got from you. Read more

My appliance is a Whirlpool Accubake Wall Oven, single door. After using the tech sheet and measuring the ohms of the two micro switches that sends signals when the door is shut and locked, determined the lock was faulty. Pretty simple to change, the most difficult part was taking the digital face off of the oven without damaging the control board. TIP: take a picture of the latch switches to ensure you put the correct wires on the correct switch. Read more

Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off. Read more

After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a... Read more

Replaced It With New One Read more

Replaced Read more

VERY simple fix- you do not even have to pull the range out.. I ordered a new cooktop from Appliance parts Pros. The customer sales rep Alphonso was great and walked me through the general process. I could find no explicit instructions for the repair but I muddled my way through. The fix is simple on Kitchenaid/Whirpool slide in ranges. 1. Open the oven door and remove the two phillips head screws directly below the control panel that hold the panel down.2. Lift the control panel upward and... Read more

Installed it according to video watched. Read more

I ordered the part; it came in 2 days! I watched the video. Repair went flawlessly! I will definitely order from you guys again! Great service and help with the install! Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

Whirlpool convection oven. Access to convection element from inside. Three screws to remove plate covering fan blade. Then one screw to remove element bracket. I placed tape over the holes with the wires so they wouldn’t pull back into the panel. Remove old element at tabs and replace. Very easy fix. Removing door to oven made it easier to get to but not necessary. Read more