Kpm26m1xer Parts

If your stand mixer runs only on high speed or won't change speeds properly, a worn governor drive stud may be the cause. This small repair restores smooth speed control in about 30 minutes.

This cap spring is a small coil that supplies the return tension a cap or button needs to operate smoothly. Replace it if weakened, bent, or missing to restore proper feel and reliable engagement of the mechanism.

• Maintains spring tension under a cap/button to keep parts aligned
• Helps the cap return smoothly and prevents looseness or rattling
• Supports consistent engagement of the related control or latch
• Typical signs of fatigue: loose or wobbly cap, sticking action, poor return, or a spring that pops out

• Disconnect power and shut off water/gas supplies before servicing
• Note the spring's orientation and stack-up; take photos as you disassemble
• Use needle-nose pliers and control the spring so it doesn't eject
• Seat components fully and test operation before final reassembly

Fix a mixer that won't turn on or has burnt electrical smell. This motor field assembly controls variable speed. Replaces worn electrical components.

White plastic back cover for stand mixers. Protects internal components at rear of motor housing. Replace if cracked, broken, or missing.

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet operation. Replacing a worn bearing restores proper alignment and helps prevent noise and premature wear on connected parts.

• Provides a low-friction surface for smooth rotation
• Helps keep the rotating component centered and stable
• Reduces vibration and operating noise
• Common failure signs: grinding/squealing, wobble or play, rough or intermittent rotation

• Disconnect power; also shut off water or gas supply if applicable
• Access the assembly per your model's service information and note part orientation before removal
• Inspect the shaft/hub and any spacers or seals for wear; replace related worn components
• Seat the bearing squarely—do not force; apply only manufacturer-specified lubricant if called for in service literature

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Fix a mixer that won't start, slows down, or makes grinding noises. This armature (motor rotor) restores reliable operation when worn or burned.

Fix a mixing bowl that won't lock in place or keeps sliding during use. This retaining pin secures the bowl clip to keep your bowl firmly seated.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.

This is a flat washer used in the drive assembly of a stand mixer. It sits between moving components to reduce friction and prevent wear on mating surfaces. Replace this washer if the mixer is making unusual noises, vibrating excessively, or if the original washer is worn, cracked, or missing.

5-quart stainless steel bowl for bowl-lift stand mixers. Replace if warped, dented, or worn. Verify your model number for proper fit before ordering.

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)

Replacement 5-quart polished stainless steel mixing bowl for KitchenAid bowl-lift stand mixers. Installs on lift mechanism with flat handle design.

Note: This is for Professional Models

Fix loose or wobbling mixer attachments with this cotter pin. Secures shafts and linkages to prevent parts from sliding during operation. Easy install.

If your stand mixer won't turn on or powers off intermittently, replace a frayed or damaged power cord. This cord restores safe electrical connection.

Pan head machine screw secures brackets, panels, and internal assemblies in stand mixers. Replace worn, stripped, or missing screws to restore stability.